Search results

Yes, it is probably misleading to refer to a heat pump always running and heating. Our's is alway in heating mode but it will cycle throughout the day and will oscillate around the set weather compensation curve point (with one defrost cycle shown below as you mention above). When OAT drops to...

I meant moreso those who are using drastic setbacks to unused rooms, but in any case radiator balancing can result in even temperatures across different rooms as of course the emitters aren't going to be precisely sized for the heat loss of the individual rooms. I think you'd be surprised if...

Sounds good, and simple set up. Minimal zoning and no buffer tank. I'd be interested to know whether anyone employing extensive microzoning within their property can evidence any savings from doing it. I tried it- zoning rooms that we didn't use much with smart TRVs and closing doors one...

Glad it is working well. What heat pump/controls did you go for? I’m running ours on pure weather compensation now. No room influence/thermostats and single zone. Works very effectively.

Can you not get a CH pump that displays the flow rate, or get some form of flow meter so you can see exactly what is going on with that side of things? Our ecotec (got rid of it now and installed different system) I remember used to cycle a lot. One particular issue was self inflicted as I was...

Hi all, I have a LED strip to install in one of my kitchen cabinets. I have the 12v LED driver which is powered by an adapter which I need to plug in somewhere close by. I have the supply side of things sorted- it is just where to mount the socket. I am guessing a surface mounted box somewhere...

Yes. Recommissioning the two white plastic elbows in the ‘top’ kit, and even then they are different pieces/lengths. Just seems such an untidy solution all round, and the sink was not cheap.

If you mean the connection here between the black piece directly under the pop up waste, and the white elbow.... Yes that comes apart. I spoke to the retailer today in fact (a separate issue is that one of the pieces is broken so I need to get it replaced) and they said that I should just...

Thanks- I suspected the main thing causing me strife trying to work it out, is that the fittings provided are rather over complicated. Strange kit to supply with the sink I have.

No it's a double sink. One overflow, with the pop up wastes.

Thanks.... I think I've figured it out (or part of it). The nudge above resulted in me having a proper look in one of the kits I've been sent and there is indeed a coupler so that side of things is sorted. The instructions though I cannot work out. I've been sent the drain kit which is this...

Hi all, I have a Blanco kitchen sink that I need to install, and it came with a waste kit. I have noticed however that the outer diameter of the waste pipe is a few mm narrower than the standard "40mm" solvent weld pipe I have used for my waste run behind the cabinet. Photo attached (bottom...

Sorry one more question. Is there any reason why I can’t do cable to the cooker switch, and then use 3 way wagos in a junction box to split and supply the two ovens? I have some room in the void/under cabinets where I can put the box

All noted and understood, thanks all. That is why I wanted to ask on here :)

Right I think I follow now- I was thinking about it the wrong way around and dual outlet plate first. What I should do is have one cooker switch, and then my cable from this cooker switch goes to the dual outlet plate to wire both ovens?

Thanks @EFLImpudence sorry I meant what switch rather than cabling. Presumably I need some form of isolator? That is what I wasn't quite following with the advice around not needing to isolate separately- which completely makes sense but then I thought I'd have to do this anyway as they need to...

Thanks again. So I can get the dual outlet plate, mount that on a 35mm back box in wall? I then have my two cables for each oven. See where you are both coming from (and agree) with the point around when am I going to need to isolate them separately. What should I then be using in between my...

Ok thanks both. I think in fairness I am probably overcomplicating this. The other factor I need to consider is that I only have 30mm clearance behind the actual cabinets so I'm struggling to surface mount anything. Thus looking at the duel outlet plate it only seems to come with the option of a...

Thanks pete01. That potentially looks ideal, and the solution I was struggling to find.... So something like this? https://www.tlc-direct.co.uk/Products/AA45DCOP.html Then the two flex outlets at the bottom would feed each appliance (oven and microwave oven), presumably via a FCU so I can...

Thanks I've already had advice around the diversity and what circuit to keep it all on. It was more for the actual hardware I need in terms of fused connection units etc. Each oven is rated at 3kW. Hob is 7.5kW