Search results

If I understand it correctly, then the answer to your questions is yes. And it is really important to secure the rockwool, to allow for sufficient ventilation underneath on airbrick level. I am doing something similar in my victorian terrace and am using some netting and a cheap electric...

I have used JB Weld to seal up a cast iron fire surround. Mine just had an old rusted hole about 5cmx10cm. So I JBwelded a steel sheet to cover and painted it. I don't know if it would hold up your surround, but that stuff is very strong! Use gloves! Once it's dry it should be safe this is...

I've purchased Hager as well for a severed cable, but they are quite large. End up using a QuickWire JB, which is very space efficient and MF. See right picture here.

Let me add a bit of context, as it is not so straight forward (at least to me). I have had a bedroom converted into a bathroom. This obviously means new drainage etc and building control approval. The works have already been completed and my installer is looking to get a building control...

Hello everyone, I just had a visit from my LABC for some plumbing works, mainly inspecting external waste pipe runs. The works they were meant to inspect were all fine, but annoyingly they have noticed some other close but unrelated waste pipes that were not up to regulation. Some minor points...

Last time I checked, they do not. But my level of knowledge might be out of date, as I was unware that you can now fit RF inserts straight into the alarm module, and keep the old wired base. in that case yes no need to change base! Well thought-out Aico.

Yes it does. Aico does RF for each series afaik, and you can mix and match. However in order to link the hardwired interlinked ones with RF ones, you need to swap the base on one of the hardwired ones (for the signal) and then for all the other RF once you need the RF base in addition to the...

Last post on this... I finally managed to finish this project, and quite proud of my work. Installed 3 smoke alarms + 2 heat alarms (all Aico) over 4 floors, all interlinked and mains wired. Had to open up a small bit of wall in four different places and drill through 3 noggins that were in the...

Finally had some time to work on this again. Cleared out a lot of the debris. Ended up not using the Hager, but instead a Wago with line for the 3-core and a quick wire for the 2.5m T&E. After pushing everything inside the void it actually looks quite decent.. no significant strains etc. I've...

I ended up using a small bit of washing up liquid, wow what a difference it made! Thanks all.

I am aware and note that you have suggested it already too me. I have done it the hardcore mains wired way now, so here we are.

Thanks all. hahaha. Certainly latex sheathing friendly in case that actually exists... It is for my mains wired interconnected fire alarms, which I am in the process of installing on every floor of my house.

Hello all, I want to pull a light wire through an extremely narrow wall space in between two wooden studs. There is about 15mm width (but +100mm depth) and to make matters worse, there are already 3 cables going through this space. And to make it even more challenging, the cable I want to run...

Probably overkill, but I went with a Gebo repair clamp specifically for copper pipes... seems rock solid. Spoke to my plumber, and he was not too worried about it actually. Given that the area is accessible he recommended to check it once a year or so. Thanks for everyone's response.

like I said.. is was requested in the written quote from my electrician. I don't know if it is common or not (apparently not), I am just providing this information and you (or the op) can choose to ignore it. really simple.

yeah. when I had my solar panels installed the electrician specifically required double boarding and some other things... In the end there was no double boarding (or at least partial) and nobody complained.... I guess if you need to lift up heavy materials they might deem it safer... although a...

+1. I saw prices ranging from 600 - 1500 for 12 weeks hire so definitely worthwhile to compar. Make sure ladders are included (should be default really) and a rope pulley. Some tradesmen require double boarding, depending on what they do.

Test

Thanks for responding. I don’t have any solder, any other way for securing in a DIY friendly way? Ideally I would like to avoid to drain the system.

Hello, during some re-wiring I noticed that one of my CH microbore copper pipe had a small nick/scratch. The floorboard had a small piece of metal pushing against it! It is not leaking and may have been like this for years, but keen to hear your views. Does this absolutely need to be...