Search results

Cheers. To be honest I dont know if it has ever worked. Can I buy a "entryphone london" handset and connect or would I need to get them in to do it?

This is the main panel. There is a company online also called entryphone so I will call them on Monday and see if this is one of theirs. If there is a way to wire up a new one that would be prefered over calling out an engineer.

It certainly looks cheap and is unbranded. I don't mind buying a new handset I just want to know I will be able to connect it.

The door entry phone has been pulled off the wall and I need to rewire it to operate the main door. Unfortunately none of the wires are left in the connections for me to see which wires go where. The cable looks like a Cat5 / bell wire with a number of coloured wires. On the right the...

Ok that answers it then. Don't want to ruin the last bit of work.

Hi everyone. The house refurbishment and extension is now finally finished after 3 years. The final job is to top the driveway and paths down the side if the house. We are going for resin bound gravel and already have the sub base laid in prep for this. As 1 last job to do I am considering...

Tha ks everyone. Thought it was ok but wanted to check. 16amp MCB. Wired in 2.5mm T/E

Nothing in the bathroom. The spur used to feed the UFH for the bathroom but was located in the hallway. The spur/socket/rad are all located in the hallway.

No the spur/socket is in the hallway

Hello everyone. I have a radial circuit that feeds an UFH matt and heated towel rail via 2 fused spurs. I have done away with the UFH and want to replace with a small electric radiator (330w nominal power / 125w effective power). I believe I am OK to connect the rad via the feed previously...

Tried an aav it no good. Will get a plumber in to see if they can identify the problem. I nodded through to the svp and there doesn't seem to be any blockage there

No pics of the original sorry. Where should the valve be located? Something like this? https://www.toolstation.com/mcalpine-vp2-air-admittance-valve/p36620 Is there one that can be connected to the 2nd spigot location? Spigots now facing up

Pictures below. There water runs from the sink to the last inspection point so there is no blockage. Water doesn't drain from kitchen sink unless an inspection cap is removed.

Yes it does. What would this point towards? Is it some form of vacuum.

Forgot to take pics but will get some tomorrow. Lead pipe disappears into the party wall so you only see one end of it. There was a collapsed straight joint below the bath which caused everything to back up and fail. Ripped it all out and replaced. Sink is existing but waste was new. When I...

Hi I have just run a new 40mm waste pipe in my flat. It drop from the kitchen sink down to low level. Through the wall into the bathroom where it falls to the original lead waste pipe. Bath is T'd into it about 1m from the final connection. Everything is new appart from 1ft of lead that...

Power shower will sit before the pump. Not sure if it has its own direct feed. Need to check. It's a rental. Does that matter?

I need to get it done as quickly and cheaply as possible. At some point the entire flat is being ripped out and remodeled but not now so just looking for an easy win. If the pumps are an issue I will just leave it with the weak gravity feed.

Hi I haven't been on here for a while. I hope everyone is doing well. I about but am about to pull out an old bathroom in a flat that needs renovating. The water is fed from a tank next to the bathroom but being a flat is only at say 1.5m above floor level. The water pressure is p!55 poor...

I know this has been asked several times before but I haven't seen one for a few years and wondered if these are still the best screws for external decking. The deck is a 20mm thick Iroko board fixed into timber bearers. Are these -> > LINK < the best screws to use? Is 50mm the correct length...