Search results

  1. Nerdish Nerd

    Identify ADT Control Panel

    More likely a 9651 considering when ADT fitted these. There will be a couple more steps to do because there is an LCD screen on it, and it is technically more advanced than the 9800+.
  2. Nerdish Nerd

    omnicron 7000

    I was going to write out how to do it but I thought "Hang on, this is a public forum" and then deleted everything I wrote because I thought I might be being stupid and releasing a little too much information on the alarm panel. Besides, before I had a massive break from this forum I saw a fair...
  3. Nerdish Nerd

    omnicron 7000

    There is a manual somewhere. Either it's an internet search away with "A1 Omnicron 7000 Engineer Manual" in the search bar, or visit the alarm manuals sticky at the top of the Alarms and CCTV Forum page.
  4. Nerdish Nerd

    Yale alarm "AC failure"

    None, it's burned into the board itself. It's designed to do it, to remind the user that the alarm is setting.
  5. Nerdish Nerd

    Yale alarm "AC failure"

    Check if all the detectors, door contacts, external bells and the panel itself to see if one of the items listed are partially closed and then giving out a tamper signal. If you've made sure every component of the system is closed up and working, then try again with setting the alarm.
  6. Nerdish Nerd

    Euro Mini Hard Reset

    There aren't any reset pins on the panel. My mistake, should have known about it.
  7. Nerdish Nerd

    Euro Mini Hard Reset

    If you want a hard reset then try find some reset pins on the panel logic board. I'm sure newer panels still have them.
  8. Nerdish Nerd

    ADE Accenta G4 Alarm Help

    It's in tamper mode and the keypad has locked out. Make sure you've closed the panel up correctly and made sure you haven't dislodged any of the tamper wires.
  9. Nerdish Nerd

    Accenta 8 Alarm Help

    Usually you press PROG then your code, then you're in a test menu. Press 0 and you can open the panel lid. To close out of engineer's mode you press RESET twice.
  10. Nerdish Nerd

    Accenta 8 Alarm Help

    It's an Accenta 8, so it was made by ADE and is most likely in a large case.
  11. Nerdish Nerd

    Accenta 8 Alarm Help

    The PIRs are clicking because that's the relay disengaging and re-engaging. Buying newer PIRs will reduce that click, but the sound won't go away for ever.
  12. Nerdish Nerd

    Accenta alarm beeps every ten minutes

    The beeps are a servicing warning after it has been set over 500 times If I remember correctly. The Accenta 6 that was in my house had a shot battery that had been in there ever since installation. Never beeped once.. until it crashed and was removed.
  13. Nerdish Nerd

    Mains powered siren

    Not as much as you'd like though. Get something that is quieter than that siren even on low volume.
  14. Nerdish Nerd

    Isolating switch for external alarm bell

    One, good riddance, and two, what the hell was he going on about? Perhaps that is why his name is "Dunce" due to his seeming logic deficit. We're being constructive by telling you how bad your idea is. Look at all the other threads. Advice is given. 'nuff said. I've probably spoken more than I...
  15. Nerdish Nerd

    Isolating switch for external alarm bell

    Correct me if I'm wrong, but it seems you don't really trust your system hence why you would like a bell cutoff switch installed. Seriously, like others said, unless something isn't installed correctly it should be all fine and dandy. It may take time, but your alarm system may turn into your...
  16. Nerdish Nerd

    Scantronic 9651 low batt beeping

    With all this said, get a decently sizeable battery. Scantronic states that a minimum for panels like that is 7 amp hours. Either get that, or one that is bigger, but not too big to physically not fit inside the panel.
  17. Nerdish Nerd

    PIR Battery Change Advice?

    If it was as simple to take down the PIR and take out the batteries without a tamper alarm it wouldn't be useful as an alarm. I think you'll find a product details sheet and install manual as a .pdf online. That's your easiest bet. Otherwise, I'm sure someone on here will have the manual for...
  18. Nerdish Nerd

    Scantronic 9448+ and 9427 Key Pad - No Mains Power ?

    If the main panel power LED isn't working then there's a problem with probably the LED or something. I'm guessing the fuses are in good condition since I think that's already been said earlier. The beeps from the RKP are usual since the keypad will beep when 12VDC is applied to it.
  19. Nerdish Nerd

    Scantronic 9448+ and 9427 Key Pad - No Mains Power ?

    Really depends on how you installed it. I know the really old 9448 and the closest that I've got to a 9427 keypad is a 7400 RRT that I managed to get the power LED to fail like the one on your keypad. Apologies in case this has already been covered but is the power LED lit when you are not in...
  20. Nerdish Nerd

    strange problem setting alarm - please help! :)

    The beeping on countdown means a detector is being tripped. If the beeping continues and exit faults the alarm (making all keypads and internal speakers sound the alarm tone), a detector is being constantly tripped. For example, if there's a door open. If the beep turns back into a constant...
Back
Top