Search results

Not all circuits are RCD protected, and you cannot guarantee the item won't be moved to such a circuit. I work for a charity, and I self-taught myself (with the aid of an online course, dvd and test) and we now have three trained pat testers. It's not difficult, the modern test tools can be...

Unless it's worn off, there'll be a plate or sticker on the item itself with the wattage of the motor. Easy conversion to amps once you know that.

Yes, blue mdpe. Hosepipe will go very soft in hot weather, and if under pressure is very likely to come out of the hozelock connectors. The modern fittings for MDPE are very good and very easy to use. The pipe is cheap and once done will last for yonks. It withstands freezing well too.

I've had cause to look into this a bit too, as it's a question I was puzzling over a few years ago. Fitting it between a sheet of plasterboard in a ceiling is not going to be that useful as the plasterboard may fail, and the extra pressure exerted by the intumescent strip expanding may be...

If you keep an inhibitor in the system, corrosion will be cut down to the absolute minimum. The only time corrosion can happen is when fresh water is introduced carrying oxygen. As for testing - pressure test? Increase pipework pressure to a much higher than normal rate and if there's a...

In the pro kit, it shouldn't be possible for the blade to ever reach back far enough to hit your toesie-wosies whilst wearing a proper harness. (Ok, you /can/, but you do have to struggle a bit) DIY stuff, no idea, but I imagine it's a lot easier to do yourself a mischief. If it's just a...

Coincides with: 1. New ways the bad guys find of cheating the system. Ie, panic stops. 2. More litigious injured people and ambulance chasing. Lot of people get whiplash now, genuine or otherwise. 3. Cost of repairs has gone through the roof since they made cars safer. Airbags (ours...

With the shift towards CFL's, they won't discolour the ceiling. As someone slightly above the average height, don't put them too low either. Logic suggests no part of the fitting should be below 6'6", same as doorways.

Sometimes, if you're lucky, you can find instructions via google. Unlocked an orange Samsung that way.

Does the motor stop at the same time as the blade, or continue spinning? Does it have a belt between the motor and the blade? If it does, it needs replacing as it's worn out. Alternatively, there may be some kind of clutch involved to prevent motor damage if you stall the blade, and...

http://www.fancyacar.co.uk/car-insurance/cheapest-cars-to-insure/ Spares costs factor heavily on insurance costs, and jap stuff is expensive that way. That said, so many cars are designed to practically explode at the first decent ding to protect the occupants it's ridiculously easy to...

Not heard that before, what's the source? Certainly nobody I knew in the game did that.

I'd be worried! Not about the water itself, but what sort of water is it? Pea shingle isn't usual for a soakaway (although it can be used - but it hasn't rained for a while, why hasn't it soaked away if it is?), but shingle /is/ used extensively to bed pipes, including mains water and sewage...

Surprised this wasn't pointed out in both surveys. Be polite and give a /reasonable/ timeframe to complete the works, but unless there is a covenant in place (sounds unlikely) then he needs to get his **** outta your house...

Best way to clear the airlock is the old hosepipe between the cold and hot taps with both turned on. One minute and shouldn't need doing again.

Totally agree with keenedge. Sorry that you've gone so far down this path but you should have done your research earlier. Don't waste any more time, they'll never be suitable, always smell and will probably be carcinogenic too.

Possibly split diaphragm in the carb or a split fuel pipe. A few quid and easily DIYable, but unusual in so new a saw. Could be a fuel pipe not pushed home on the stud properly, crap fuel, dodgy mixture (check colour of plug - should be a light biscuit colour, but with air getting in this can...

Hi. Something like this will do. 5 minimum, more if the brick is that week. http://www.screwfix.com/p/fischer-universal-frame-fixings-10-x-160mm-pack-of-10/94107

Surprised nobody's answered, so fwiw, I will! Cannot see a problem provided you're drawing out of a tank via an essex or surrey flange rather than the main feed. You may want a bleed vent at the upper part of the 'n', preferably off a short vertical spur to allow the air to collect and...

Betula Pendula! Hah! Saw this post this morning and thought "I think I know, but I'll wait for an expert to comment so I don't make an arse of myself". Don't seem to be any of them so far, so... My guess is it's a cherry of some sort. Definitely a fruiting prunus of some variety, but...