Search results

Cool thank you! I've changed the speaker now and it works on a speaker test now. I also want to change the sound when I arm the system. My old texecom when full setting would beep while arming, when part setting it would be silent and then give a single beep after me going upstairs to indicate...

ok, I'll change that, I thought I'd read it on another thread, must have been confused. What about the control panel's flashing green light? Is that normal?

Couple of little issues, I wired the internal speaker to OP1 and programmed it as area alarm but it doesn't seem to work, is that the correct programming? Also I noticed the Control Panel's green light is flashing, I'm sure on my old panel it was solid green, although everything else is working...

All working a treat now, full set and part set. Will connect the bell box today. What do people generally do regarding the users, I'm planning to change the engineer code, do people use the master user as the normal user or should I create a new standard user for us to use? One user for the...

ok, so I named the zone and send the details, this seemed to have wiped out the fact I was using a smart com, I re-configured that again and its connecting again. How do I prevent that happening when sending data to the panel?

Well I was sorted, it disconnected and now will not re-connect, painful :)

Sorted, I've connected to it now

Wintex doesn't seem the most intuitive application, I'm completely new to it. The manual doesn't say anything about connecting via smart com. Firstly, I don't see how wintex know's how to connect to the panel.

I notice on the RKP that the ready (tick) light is not lit. There are no errors??

I re-wired all the PIR's an now the walk test works as expected. Strangely when I try to arm the system it does nothing. Also I was led to believe that I could connect to the system using wintex via the texecom connect but its not obvious how to do that, is it possible?

Hey sparkymarka, yes that was exactly the problem. Just confirmed that with one PIR and re-did the walk test, working now. Will change the rest. Getting there!

Just gone back to the PIR wiring instructions, looks like I have wired them up incorrectly. Will change one and test it.

I knew that ;) not sure why I missed that on the programming. ok, so when doing a walk test my door contact and panic alarm work correctly but none of the PIR's register on the keypad although the lights on the PIR do. All PIR's are set with the 4k7/2k2 jumpers using right tamper and left alarm...

My PA is wired as below, does this look ok compared to panel?

Update, power on now, couple of errors, box lid tamper, RKP tamper and zone 7 tamper). box lid of course as the CP is open. I hadn't adjusted the screw in the back of the flush mount RKP panel, adjusted that to fix the tamper. Not sure about the zone 7 tamper at the moment, thats the panic button.

I've managed to do a little more this weekend, I've wired up all zones now. Z1 - Door Contact Z2,3,4,5,6,8 - PIR's Z7 - Panic button Hopefully this looks ok? All pir's are wired like this. Haven't connected up the external siren box or internal speaker just to minimise the noise while...

Bit of a delay on this thread, only just getting round to wiring this stuff up. Does this look of for the wiring of the door contact? thanks Marvin

Ok, so a bit more reading on this and I think I have found what I need. For the door contact I will use 2 core fsl with the 2k2 and 4k7 resistors which then just wire back to the zone on the control panel. For the PA, I think again I can simply wire using 2 cores to the contacts in the PA either...

I think I’m almost there now, happy with the keypad, external/internal sounders and pirs. I’ve got to add a door contact and panic button but just trying to get my head around the wiring for these. The door contact I’ve got is this one...

Great, thanks for clearing that up!