Search results

I want to put sentinel into central heating system. Do I have to drain out all the water or can I do it without draining out. Is it possible to just draining out one radiator. I can see there is drain out pipe connector in downstair radiators.

Update on my car: Today I took the car to the garage. The technician has found a leak in the front exhaust pipe which is just after the cat converter. I think the rear Oxygen sensor is inserted into it. I will order a new pipe, clamp and get it fitted. Will let you know how it goes.

The Engine Light is back on again after many months. Had a scan and same error code.

I have cleared the codes. I drove around 15 miles today. No engine light has come on. No sure if the performance is down a bit. Took it to the garage near my home to check. Nothing found with a scan.

I did not notice any change in Engine performance. I have done scan in other items. It found additional faults: 2 Faults Found: 01598 - Drive Battery Voltage 07-10 - Signal too Low - Intermittent 00906 - Shareware Version. To Decode all DTCs 28-00 - Please...

My Car Engine Light is ON. I had a scan with VCDS Light. The result is as follows: VCDS-Lite Version: Release 1.1 Monday, 24 September 2012, 18:14:52. Control Module Part Number: 03D 906 032 C Component and/or Version: 1,2l/2V SIMOS3 00HS2501 Software Coding: 00031...

The technician at my local garage has identified that there is leak in the absorber and the spring is broken. He is suggesting me that I can buy a used set of absorber +Spring and he will replace it for me. Is it a good idea to buy used or shall I buy new ? I am in favour of buying new. Please...

Hi, Driver side front shck absorber spring broken. Is it possible to change just the spring or I will have to change the whole assembly ? Do I have to change both side ?

Hi, Open the battery cover. Be careful about battery. Do not short positive and negative terminal accidentaly by screw driver or any other metal. If you open the battery cover then you will find that the fuses are in that cover. This black plastic holds some fuses. I do not know what other...

I fitted a new switch and it is working now. I wasted some money on new set of brush and a second hand timer. I fitted the new brush anyway. I have n't fitted the timer. The door lock was damaged and caused short circuit. The door lock mechanism is quite sophistacated. But it looks simple. I...

Engineer told me its not worth reparing. Now I can study it before buying a new one. Of course without any electic supply. 1: Timer: I have taken note of the pin number and the wire colour. I have not taken out the wires though. I found that there is a motor in the timer. I checked...

An engineer visited my home and has told me that the timer is gone and its not worth repairing and time to get a new machine. What a shame!

I expect the door switch to be OK. Still I want to test it. There are three wires: Orange (big fat), brown, blue. Not easy to access them. I also can not trace where they have gone. There are few dozens wires bundled together. Not visible where they are going. Big fat orange one looks like has...

After further examination I found that the ends of the carbon brushes are not very nice. I want to change them anyway if that helps. I donot know where to buy these birmingham. If anybody knows where I can buy them cheaply please let me know. Buying from ebay takes few days to arrive. I want to...

I removed the motor and checked the brush. They are still an inch long each. Looks ok. How can I test if the motor is OK? There is a 7 pin connector in the motor.

I have taken out the pump. It was clogged with coins, clips etc. Many things were rusted. I have cleaned them. The pump restnace is around 150 ohm. I am not sure if it is OK. There are three solenoids. All three shows 3k ohm resistance. I have taken a picture of the motor. It is at the back...

Whirlpool W120 washing machine. I filled the machine with some clothes and switched on. The fuse went. I changed the fuse (13A) and switched on again. The fuse went again. I changed the program to stop position. Rotated the drum by hand. I changed the fuse. The program in stop position. I...

My this problem was solved by the garage in May during MOT and annual servicing. I watched what he was doing. Took out two screw and then pulled. The plastic came out. He then told me to try the wiper. There are two functions here: 1. Moving of the wiper 2. Spray None was working. He took out...

Today I went to main dealer to fetch the 40A fuse. After I replaced the broken fuse (not blown fuse) the ABS light is gone. The original fuse lasted 8 years from new. The below post helped me to solve this problem: http://www.clubpolo.co.uk/forum/lofiversion/index.php/t142584.html The person...