Search results

  1. C

    Hourly wage for a plumber

    And can gas raise that a lot?
  2. C

    Hourly wage for a plumber

    employee
  3. C

    Hourly wage for a plumber

    Plumber, at the moment
  4. C

    Hourly wage for a plumber

    In the Yorkshire area
  5. C

    Hourly wage for a plumber

    What is the standard hourly wage for a plumber?
  6. C

    Solder runs/ snots on pipe

    Thank was just worried the inside of.the pipe may look like the outside.with the snots thus effecting flow
  7. C

    Solder runs/ snots on pipe

    Just snotted down the pipe . I use a flux brush so try clean it off it runs down the pipe. Can solder run like it does down the outside of the pipe on the inside?
  8. C

    Solder runs/ snots on pipe

    Though unsightly do solder runs/ snots on pipes have any impact? I try and solder quiet neat both on show and on unseen pipe work. My colleague doesnt solder neat on pipework under floors etc and leaves snots
  9. C

    first fixing for basin

    Sorry I mean bringing the pipes up through the floor so the fall just behind the pedestal. I am guessing about 5/6 inch but as yet we have no spec for the basin just that it will be a pedestal basin.
  10. C

    first fixing for basin

    when first fixing the hot and cold for a pedestal basin but u don't have the basin dimensions what distance would u bring the pipes up through the floor?
  11. C

    15mm cold feed

    Sorry just a standard house with a combi boiler. The house has a bathroom and small ensuite. Is a 15mm cold supply enough for this. The incoming supply is 25mm mdpe. Do you need to know pressure etc?
  12. C

    15mm cold feed

    Is a 15 mm cold feed enough for a house run of a combi with a bathroom and.suite. As long as there is enough pressure. Obv. Feed off 25mm mdpe
  13. C

    First fixing a house hot and cold in 15mm

    Thanks I realize the combi may struggle but were I work always fit combis is a price thing I think. Will be a 30kw combi though. Was just worried the one 15mm run feed a shower and bath in separate bathroom maybe an issue? But the whole house is pipes in 15mm. So can't see how teeing of the main...
  14. C

    First fixing a house hot and cold in 15mm

    when first fixing a house off a combi. And the hot and cold pipes are 15mm through out. Is it ok to tee off the main run of hot and cold pipes once to put up 2 bathroom on with a bath and one with a shower. The only other supply's required are to a cloak room basin and toilet. Am I right in...
  15. C

    condensate fitting in wall

    So its ok that you d d never know if was leaking, would glued be better than push fit?
  16. C

    condensate fitting in wall

    the condensate is in a wall chase which will be behind the dot and dab plasterboard. the condensate will then go in to a 32mm elbow exiting the building through a 2inch cored hole so not on show. So the one side of the 32mm elbow will be well in to the wall. Is this ok, because they won't no...
  17. C

    Forever white silicone sealant acetoxy cure?

    Is foreverwhite silicone sealant acetoxy cure? Just worried about corrosion to copper?
  18. C

    Gas pipe underfloating floor

    There is a screed that the pipe will sit on before the insulation is placed on top. Though damp course could be put down so the pipe sits on this
  19. C

    Gas pipe underfloating floor

    If a gas pipe is ran under a floating floor, under the boards and insulation should it be either coated or taped copper?
  20. C

    Savisto pop up bath waste

    Any help?
View older results
Back
Top