Search results

Is it a 1" bsp male or female thread you are trying to reduce ? If its female you can buy a reducing bush at plumbers merchants to take you down to 1/2" bsp .Which should suit the male thread on your shower head or if female shower head fit a 1/2" x1"" nipple .Hope you understand this.

Have to put to me hands up and admit have had a hot water flush on a lav before (handy in the winter a suppose)

Get your brother in law to buy a replacement bath , or try and source taps or mixer taps with a bigger base to cover holes .Suppose you could try and do something to reduce the diameter with fiberglass resin and filler what every good car accesory shop will stock (worked on the holes in me van...

could poss be A water level in cistern to low B your syphon is at fault either a split diaphram washer or a split in your syphon OR if its one that has a nut to disasemble the syphon it may be loose C canny think of a C !!!!!!!!!!

Yes can be .no are noisy i replaced one just the other week the sponge like float valve inside has a habit of sticking . A sharp kick usually does the trick if not lid off hand in and ughh.In my experience they only last for a couple o years A would try other radius bends and as other post says...

Dont want to be a spoilsport am not 100% sure but a think in our neck of the woods your not permitted to have a saniflow if this is your one and only crapper in the house . They were designed by the devil himself any way flaming useless avoid!!!!!!!!!

Similar thing happened to me a few years back didnt let the side down though still got paid as well .Only thing every time she spotted the van she used to hang about stalked me for months.

Think there is what son :?: Sounds like your being a wee bit facetious here

The guy just said the cylinder access is a pig so does this not defeat the purpose son

no chance twin system in most areas regs will not allow

If it is as you say push button without more info will poss be the button on cistern lid is needing adjusting, Button not allowing flush to spring back so drop washer not sealing allowing constant run.Witout seeing it try pushing [should be two half moon shaped plastic bits] up into lid while...

only reduce the flow by nipping back valve ,pressure remains constant. Thats why we had to go to and still do at great expense to college which is reflected in our invoices.

Used to be known as green rings .the middle was coloured green once but must be to dear to do it now. So now ye canny find them in your box of bits and bobs!!!!!!!!!!!!!!!!!!!!!!!

Should be just a quarter turn ,But seeing as it could now be either half open or half shut [depending on how your mind works].Turn on your kitchen tap and turn valve a wee bit at a time untill hey presto water should stop if its your valve that is .But a would get an internal valve fitted as...

U got the washer fitted right? Goes inside cistern ,tighten up by hand 1st to ensure its sitting in the middle.Some times you can have a wee bit tension on the supply pipe putting a strain on the body .Tighten up bottom nut before you attach supply pipe.failing that put a bucket underneath!!!!!!!

Never heard so much tosh in all my life.If it was gonny leak it would have done it by now .If anything it would crack or leak at where the sections join together.

It Will if you let on you no he haw!!!!

If constructed right should be ok as long as the membrane and tiles are laid /fitted properly. Would not go for it myself though as i live in a bungalow!!!!!!!!!

they are prone to crack coz years ago hole saws were scarce and expensive so the inovative plumber would heat up a length o pipe to form the hole which hardened the polythene resulting in a weak spot [ just thought you would like to know!]

Like the man said claim off the insurance and you get a dafty like me sent round .Pain in the butt to replace got to remove screen ,1st trying to take off old silicon then smash old 1 out .New 1 never fits or matches up to tiles ,The drain connection is always a tad awkward what with tiled an...