Search results

thanx chris but I need a modern digidal programmer ,with more than 2 setings @ day, to fit my Kingfisher 60. I saw one mentioned (P.No.5107754) but cannot find the shop that sell it. nick

Can I fit an external programmer (modern digidal) to Kingfisher 60 to operate remotely from the kitchen? The boiler is in the garage15-20m away. thanx nick

alas no name but has 5 wires !

Hi, I have a door speaker for the front & one fro the rear door, but oly one Han set, whitch works the front door. Can I connect the rear speaker too on this one hand set? Tried various combinations of the 5 core cable but only get an high pitch baz. thanx, nick

Hi all, if anybody uses this particular cylinder can you help? I have an OSO Hotwater Indirect Cylinder 250, Non Vented with two Electric Boxes, the upper has a "Thermostat Boiler" & the lower one an "Immertion Heater Thermostat" both set at 60. 1. Should these be at 60 for summer &...

many thanx, will use P.mait. nick

Thanx you all, probably the last sugestion is as applicable as any, except for the SILICON. The others are somewhat vague. The Screwfix you give says "30% stronger than traditional silicone. Mould-resistant and waterproof". Anybody used tis one:- code 45463 "No Nonsense Intumescent...

The ceramic hop instruction says use a sealant BUT NOT SILICON round the inside of the cut in worktop. B&Q etc. all say they do not have a Non Silicon type. Can you advise please? thanx nick

There was hidden a 50A switch after all. From its position it would be more convenient for the 6mm cable out of the 32A MCR to go direct to this switch & avoid extra wiring. I hope this will be in order. nick.

There was hidden a 50A switch after all. From its position it would be more convenient for the 6mm cable out of the 32A MCR to go direct to this switch & avoid extra wiring. I hope this will be in order. nick

Thanx, there is a Cooker Connection Unit (with slanting face & cable exit at the bottom), low below cooker/hob position, with 6mm cable coming from its own 32A MCB, will it need a DPole switch too, or just join the ceramic hob direct to the C.C.Unit. nick

Thanx, there is a Cooker Connection Unit (with slanting face & cable exit at the bottom), low below cooker/hob position, with 6mm cable coming from its own 32A MCB, will it need a DPole switch too, or just join the ceramic hob direct to the C.C.Unit. nick

Installation via modern split circuit Consumer Unit. 1. Moffat (Electrolux) fan assisted Oven (Total Rating 2,075 W) its book says it needs a double pole 13A min, & min gap 3mm between the switch contacts. I have an oldish "Metal Clad Double Pole Switch 13A with red neon light", how can...

Installation via modern split circuit Consumer Unit. 1. Moffat (Electrolux) fan assisted Oven (Total Rating 2,075 W) needs a double pole 13A min, & min gap 3mm between the switch contacts. I have an oldish "Metal Clad Double Pole Switch 13A with red neon light", how can I find if the gap...

I am building a room partition of 4x2 studs & plaster boards, which is best for soundproofing infill, fiberglass wool (used in lofts) or polistyrene sheets/blocks ?. Thanks, nick

Thanx again, will apply this info to suit the bangalow drop-down pipes to rads. nick

thanx LUNAT, where / what is "Filling Loop"?, nick

Thanx, on filling it with Fernox method, do you have to drain away the system first, or just keep toping it up? Nick

In my old vented system I used to change the Fernox every 2 - 3 years. How is it done with my new CH system? Potterton Kingfisher M F 60 boiler, with an “OSO” Unvented Water heater. Also has a second expansion vessel (Zilmet) with pressure gauge, a fully sealed system. Thanx...

Hi Again, Recently I asked help on above subject (see my inquiries about this here :- http://www.diynot.com/forums/viewtopic.php?t=119853 After all your advices, eventually I found a young plumber in my area who quoted a very fair price, he undertook the work Mon 25th Feb & finished...