Search results

it's 247. the same as my wall plug. (i connect one DMM probe to earth and one to the white wire)

http://leegate.f2s.com/mid.jpg As you can see in the picture, I measured it between the two orange wires, from left to right, the 1st wire and the 3rd wire. Black probe to 1st and red to 3rd , the reading is 50v Red probe to 1st and black to 3rd, the reading is 94 v. I have a reading...

thank you. the voltage reading is 50 or 94 between the two orange wires, does this sound correct ?

yes, I open the cover and see five wire: grey, orange, blue, white and earth. which two wires do I connect the multimeter probes to ? is it correct that I the meter knob points to upper right dial marked V 200?

ok. I have one of this multimeter http://www.doctronics.co.uk/images/meter2.gif which position do I need to turn the central knob to check for power.

thanks seco. the heating light on the timer is on when the room stat clicks to call for heating. but the actuator still does not switch itself from W to H to get heating. It only goes one way from H to W to get hot water. I have a digital multimeter from maplin. what should I check for?

my 3-port mid position actuator seems to have developed a fault. it only responds automatically to hot water calls but not heating calls. I have to manually push the lever from W to H position to trigger boiler to get heating. The model numbe is BGMVSP-23. I have learnt from plumbing forum...

thank you seco and twgas. I tried and turned off HW and turned on heating, the lever does not move to H automatically. however, I can move lever to H by hand. with a meter, what sort of voltage should I look for?

thank you for your reply. I can hear clicking sound when adjusting the room stat to increase and decrease temperature. timeclock is digital and it's BG brand. When CH light is on and HW light is off, the actuator still points to HW, it can not switch itself to CH. does this mean...

hello, my mid position actuator only switches itself to HW posistion and not to CH when called. however I can use the manual lever to move it to CH to get heating. The model is called BGMVSP-23. it has W-M-H three positions and has lever on the opposite side of W-M-H. Don't know what it is...

Indeed, a good and accurate diagnose would make a lot of differences. I had a plumber around, who did boiler service last month, but he did not pick up any fault then. I guess diagnose was not part of boiler service. I have had to use reset for some time, at least two months until this...

Sounds the way to go. Is the £220 current heateam charge?

thanks Tony. Which plug is for gas valve? When I switched off the boiler power supply. the red light went off as well. My suprima is about 5 years old.

Thank you for your reply. No, it is not firing up after reset. not even green light. what can I do with the gas valve?

I would like to pick your brain: The red light in my boiler is now flashing and the pumb is spinning. I have tried reset button but no success. not sure if it needs a new PCB or not? Since not insurance policy, I appreciate if any of you could help me to get it work again. Many thanks.

Hello, My neff cooker hood/extractor stoped working this lunch time. I can hear slight noise coming from the motor when switched on by pulling out door. It has a paper filter which get saturated with grease in a few days. I appreciate if any of you can offer some tips on how to...

Thank you nigeld, yes, I have found them and I have pulled out the oven. Mine have two screws. now i know that It is a slot-in type oven. Once again, many thanks for tips.

hello, I would like to know how to take out a fitted single oven. it is a NEFF brand and powered by electricity. Many thanks for any tips.

thanks for your replies. Sorry for not mentioning that the drainage is routed with straight pipe into the manhole via an opening next to manhole frame. but it does not have a trap and its does not seem to fix to any pipes inside manhole since I can lift the straight pipe up. 1) what is a...

The waste pipe from my washing machine feeds direct into drain via an opening in the ground beside the manhole frame. the opening 6in by 3in (about 15cm by 7cm). The manhole is beneath the fitted washing machine. there is 10 cm of clearance between bottom of washing machine and floor...