Search results

spotted these.... http://cgi.ebay.co.uk/Lift-N-Roll-Appliance-Moving-Kit-Wheels-/180481983158?pt=LH_DefaultDomain_3&hash=item2a059082b6 Guess you could fit these at all corners,move the appliance into the space and then remove the front two? also...

Have you cleaned the pressure chamber and the transfer pipe as in the pics below? http://www.ukwhitegoods.co.uk/modules.php?name=Forums&file=viewtopic&t=44514

Well its not very difficult to change the pcb but imho it isnt worth spending mega bucks on a new PCB. A good option would be to try a 2nd hand outlet or Ebay for example ifyou really cant live with the lack of the feedback led. The other option put the few quid towards a new machine. With...

You can see some diagrams of your machine on the link below https://www.bosch-eshop.com/eshop%28bD1lbiZjPTA2MA==%29/bosch/gb/prodp.htm?prod=SGS45E68GB%2f64&ESHOPTYPE=A you need to dissassemble the pressure chamber (0410) and also clean the pipe from it to the sump(0430) Check the...

sounds like you need a new door seal about £20 and fairly easy DIY

Aquastop is the Bosch external water inlet valve and simply should just switch on or off. Not aware of any noise from these but then again I have never seen one go wrong. Do you get the noise all the time when the machine takes in cold water? This can be maybe 4/5 times during a full cycle...

Check that thedrain pump filter is fully screwed in and that the pipe connections to it are fully secure. Look at your manual or if you dont have one they can be downloaded from the Bosch support site

You may have reduced circulation due to a clogged up pressure chamber and transfer pipe to the sump. Power off and remove lid,lhs panel(two screws door frame)lower plinth and metal plate. You should see a pipe running from the pressure chamber to the sump. This tends to crud up leading...

Searching the internet I found the excerpt below: The "F16" on a Bosch indicates the door is open / unlocked. If it's happening during a wash it would suggest either a faulty door lock, faulty wiring or worse, a faulty main control board. The wash program should halt when this comes up but...

I suspect the fault code is F:06? There is a reference on this forum suggesting a fault on the door switch on another Bosch however you may have a motor fault so I would check the brushes first..

sounds like the brain has gone for sure. Not seen any kind of reset I'm afraid. The kindest thing to do is to put it out of its misery perhaps?

worth checking if the pipe to the pressure switch is blocked. With lid off the pressure switch is usually on the rhs wall at the top. About the size of a matchbox either round or oblong and will have a small rubber pipe running from the bottom to the drum. disconnect and blow through to...

If you post the model number (etched into door rim) then should be able to more specific You should first check the resistance of the heater element(25ohms) on the opposite side (depending on model) If there is poor flow then the heater will also not work so you should strip down the...

Had this problem myself and its a pcb controller or dead led issue. There is no economic fix unless you can trouble shoot pcb's Something I learned to live with -machine has worked for over 12mths without any other issues though....

Have you checked that there is good flow from the pipe when you drain(reset) the machine? I always check this with the waste pipe into a bucket and then poor a basin full of water into the machine so that it is just below the salt cap and then switch on and press the reset. The bucket...

Does the water get hot? Cycle times will lengthen if there is a problem heating. Try the machine on a cold wash to see if it completes. Also try the equivalent program on the other side of the dial ie 40 cotton or 40 mixed/delicate. you could have a problem with the pcb brain..

dont take this the wrong way but is there a "rinse plus button"? plenty of the Bosch machines haev this as an option and if selected will add the time on

If the armature has any scoring -usually directly in the middle-then it is unlikely to recover. Can you hear any ticking or clicking when the motor runs? Again sure sign of the brushes bouncing on the armature. Its a good machine and built to last -you would need to spend towards £400 to...

I am pretty sure the machine does not have any logic to decide whether it is wobbling or not.........if bearings or weights were a problem then it would be very obvious. Afraid motor gets my vote.........seen it myself on a couple of Bosch machines this year which I had hoped would be...

I would check the brushes again -the contact angle might not be good and/or brushes not moving freely in the holders(wet n dry). If the armature is damaged or uneven then this can also mean the motor will have trouble under load and/or higher speeds. When you changed the brushes was...