Search results

Why cant the brach of your T go sideways? is there no room or something?

Never worked on a J&S boiler, worked on a lot of their WAU though, they were not that bad as far as warm airs go, but then again thats warm airs isnt it

More like Britains worst D.I.Yer :lol: :lol:

Not sure is this the one with the black microswitch that clip on top of diverter with a black and brown wires or is it the one with the black square box microswtich that sits on the end of the div valve, if its the latter of the 2 then yes defo can its a geononi valve and diaphragms stocked at...

Tee into the central heating pipe if you like, it'll be funny, then you can post in here about the problems with your central heating, i love your thinking of how it will be cold in the summer when you need it, absaloute classic :lol: :lol: :lol:

http://www.ukhps.co.uk/images/WM_3.jpeg sorry can get the picture on here for some reason dont know why let me know what your thinking do you understand my plan now

Cant you just T into the horizontal pipe. Run a short piece off the branch on the tee and then get a hockey stick type washing machine drain and trap and connect to the small branch off your tee using the compression supplied with hockey stick type trap, then just sit you flexable washing...

No, but you will need a GAS SAFE registered one my friend.

If pulling the plug off and putting them back on doesnt work for you, there is a micro switch, bottom left hand side as you look at boiler, has a clear housing a common fault on these is the spindle leaks, causing moisture inside the housing which intermittenly makes the switch without anything...

Well its not going to be dne right is it, it doesnt conform to current regs, also would you buy something that contains gas, electric and water that could cause major damage and you know nothing about how it works, 2nd hand off e - bay, i wouldnt, FFS just get a new boiler tight get

Just buy a new ball valve cost you about ten notes form bnq and its a **** easy job, also if its new why is it cracked, im thinking someone overtightened? If it wasnt you, you aught to get them back

Is the AAV not inside the combustion chamber on those?

You can get the screws on their own off some manufacturers, which are only any good if you can get the stub out of the gas valve. Look a right **** though when you turn up to do a service it all working, you check inlet working pressure and snap there goes the heating and hot water, im hoping i...

I agree dont fit old boilers, regardless of regs, dont do it, if you want a cheaper option go for a new main combi 30 he exactly the same as baxi which is prob top end of the middle of range boilers in my opinion, not to trublesome and easy to work on, also applys to the new regs you can pick...

Next he'll be pushing Halstead :lol:

True VAILLANT HAVE BOUGHT glow worm, sold out when they did that, however i stand by the fack clow worms (recent) arent so good cxi's/hxi's poor poor poor flexicoms, not had to much trouble but time will tell on them

If you have a Y plan or S plan chances are yor valve is passing heat to the radiators when in HW only mode, usually down to sludge stuck in valve not allwing to fully close of CH port, if you have a gravity system it could be something like your anti graviy valve stuck open, although they...

Sorry i only work on NG, dont have a clue about the oil ones in all honesty, i thought Worcester Bosch were German and i thought Vaillant was also could be wrong though , Also form what i see a lot less of these two breakdown in comparrison with the ammount fitted, compared with Ideal which i...

Not defo, each job is differant it needs to be looked at by whoever does it and they will advise you the best route to go down, however a lot of guys dont like customer buying goods and them fitting, due to all sorts of problems it can cause, parts not turning up etc etc

I hate them do a lot of breakdowns these days, between 5-10 a day and i can without doubt say Ideal are amongst the worse boilers i have worked on, Isars and Icos's are ****e, Ideals are ****e they are anything but their namesake and if this is british manufacturing throw it on the scrap heap...