Search results

i had a similar thing happen , and the connection just came out - i managed to replace under warranty - but we are by the seaside and wet just corrided the lot - are they LED or bulbs - maybe wiggle each bulb and see if that helps - maybe there are some fuse bulbs in sections I have icicles...

sounds like lose wires - BUT it would need to be 2 lose wires if on a ringmain as it looks like from pictures or the screw is on insulation and a wobble disconnected / connected maybe maybe the screws need a tighten on the sockets - and insulated screwdriver would be good to do that with do...

and onwards - you mean the sockets in the kitchen and then in the other room from the last kitchen socket and all other sockets are working in that room except the one through the wall to kitchen maybe worth numbering the sockets just for clarity - as onwards doesnt help here so much EDIT...

1. probablly best to turn off the main switch - NOT just the MCB trip - depending on how its wired its possible to get a shock off the neutral wires - and trip the circuit anyway , if any wires a lose and happen to touch earth 3. What about other sockets on the ground or 1st floor - then so...

do you feel confidant that you can remove the front of the sockets/fused connection and pull out slightly and look at the wiring inside if so then as peter01 says i would look at 2 sockets - the end one on the right - just to see if it only has 1 cable going into it and no others coming out...

when you do get up tomorrow and start to look at the problem again - JUST a suggestion - re-read all the posts here from the start and just check through each post and make sure you have answered - as often happens , with lots of suggestions and when you are also dealing with "stress" of a...

Ok, was part of the previous post as well , explaining you picture wait till morning , when light - I'm in UK and will be around tomorrow - so can help further as i'm sure more members will also be around as this is a good responsive forum

on the consumer unit - as asked before which MCB turned OFF the kitchen you have a B32 MCB labelled sockets (maybe a RING main ) and a B20 MCB labelled sockets (Maybe a Radial or a RING split - as no labels shown on ALL the other MCB's

it should likely be a RING - a Radial its often thicker wire than i think i saw , not great photo of wire - ring 2.5mm radial maybe 4mm A RING - comes out of the consumer units - connects all the sockets IN and OUT and then goes BACK to the Consumer unit A Radial - comes out of consumer...

and the last socket on the right does NOT have a wire coming out to somewhere else ?? just 1 wire in - OR maybe the out wire goes in the wall and you cant see it

so the ticks mean working - correct ?

yep, as also asked a while back OR also

as mentioned , when you do change the fuse - if that fixes the issue then you have other issues with the wiring AND was working before hand - so that should be after the fuse - maybe its worth taking the face plate off that and see whats going on, in the morrning - but if the boiler was...

well , really should not be as if it is on a RING main then even if they have wired the ring split with the fuse, then if fuse blows - it wont stop the other sockets as they should be feed from the other side of the RING BUT its worth changing the fuse and if that does fix it - then the wiring...

so which switch was that - as you have sockets written on both sides of CU and that stopped all the sockets off that where ON - Green in picture

as mentioned

as mentioned in other post assuming the labelilng is correct - MOST UNLIKELY given the amount of MCBs so maybe well off here CU picture

is the fridge plugged into one of the working sockets and working NOW everything in the house all sockets are working except for the 3 you shown in kitchen its late now in UK - so you may want to leave any frezers ??? - fish tanks or anything else that MUST have power overnight and they are...

then should have tripped - maybe the RCD has tripped and not showing as off you have 2 RCDs with a SOCKETS shown on the label is the shower working just wonder if the RCD tripped BUT not shown as off on switch - not experienced that - so no idea if possible , but i know other switches can do...

unlikely - BUT is there another small consumer unit in the kitchen at all none of those Fused connection unit - under worktop or in cupboards at all as pete01 says I cant see why if all you did was fiddle with the toaster - BUT maybe coincedance or somethign happened when pulled the plug out...