Search results

EDIT WHAT ??

Drum bearings have gone. The drum will be banging around causing the noise, It will be blowing the trip beacause the drum has gone through the heating element. If under 5 years old then it is covered by Hotpoints 5 year parts warenty, but you will have to pay the labour of around £90

Which Lights are flashing

Yep, good and expensive, A new pump fitted by Hotpoint will cost you over £80. You can easilly fix this yourself with a £15 pump. If you need instructions then lreply here and I wil help. You may just find it's blocked and doesn't even need replacing

Hi Save your £90 and get yourself a bowl, a pair of big pliers or grips and follow my instructions. UNPLUG THE MACHINE FIRST The problem it the presure stat is not sensing, this is usually caused by the air trap being blocked. You need to lean the machine back so you can get...

If you are 100% certain that the motor is OK then check the wiring in the white plug as it goes into the motor these are prone to breaking. if not then it will need the timer/module Repaired/Replaced Hope this helps

Not quite sure what you mean, the Door interlock will take a few mins to open after a wash has finished. These door locks are prone to failure, the usual problem is the machine will not start. There is 2 versions of door lock for your machine, a 3 tag and a 4 tag one, if you provide me...

Even with the Istor ???

Still looking for any other ideas or options, Some of you are saying don't but the Istor but have not come up with any other ideas. Thanks Pat

I too am looking for a similar product, I was told that there was a good priced 35mm product available but have yet to find it. The closest I have found is this KINGSPAN KOOLTHERM I will be asking the guy who told me about it later in the week.

@ Chappers too. I was quoted nearly £4k for a sprinkler system, who was this through ??? Apparrently if your mains inlet is not big enough then you can opt for a storage tank and pump, not sure if this is cheaper than £600 but on the good side is you don't have mains pressure water...

I did realise this, when the store is empty it still throws it out at 11 LPM, This is exactly what I wanted though, Advice from you guys in the know, I just liked the sound of the thing as it was compact and complete. But I want the best for my situation. These are my requirements...

I know this subject has been briefly touched on before but this is a direct question with regard to recommendations from a Ideal Boilers regarding one of the Units. Being in Kent we have one of the hardest waters in the country, During the renovation of my house i thought I be clever and look...

I am looking for some input regarding this boiler or if you all think I would be better off choosing a different one. I am in the middle of renovating my house, it's a 4 floor one bathroom that's going to have a large corner bath. Underfloor heating . The boiler will be placed in the...

One of 2 things Bearings on their way out, will be noisey too. Not really worth repairing. Mould building up on the inside of the machine, can be seen by pulling the door seal forward a bit and you will see a horrible orangey mess, Best way to cure is stick a washing machine or...

Could be one of a number of things. Condenser is blocked, not reallya DIY job but I can give you the instructions if you like Condenser cold inlet valve failed, A bit of a fiddle to do but in the scope of the DIYer.

There is no catch or lever, you just pull it as far as you can, then pull sharply and it will come out.

When the lights start flashing which ones are they ?? the flashing lights are an error code

Most Probably the motor brushes have failed, Not an expensive or difficult job to do, should take 10 mins and you don't even have to take the back off the machine. MALE SURE IT'S TURNED OFF AND UNPLUGGED Lean the machine back against the edge of your worktop, get underneath it and look at...

Does anyone know of any companies that are providing insulation under the grant system for solid walls ?? I seem to have hit a solid 9" brick wall trying to find anyone that does. I meet all the criteria for the full grant but can't find anyone to install the required insulation :( The...