Search results

Airlock? Is your tank not very high?

I'm struggling to find connectors for a pair of hot water solar panels I have. They don't have any threaded connectors on them and I cannot find any alternatives. Does anyone know these and the name/type?

I don't think so, they do work under 12v separately, it seems that the car earths rather than "opens" the circuit. We put a diode inline on the 12v brake tab on a bench supplies and it fixes the light. Tested the LED on a new trailerboard on another car - to make sure its not my socket - same...

Issue solved - nabbed a neighbours mint condition light board - that works. Swapped the filament bulbs with LED and the issue followed the LEDs. Unless there is something odd about my car wiring that the filament bulbs don't have a problem with. Thanks for the suggestions.

I know they're the correct way as I can push them in reversed and they work(the fault) in the opposite direction. The problem is when the brake pin is connected without being on, it seems cuts out (as if its grounded instead of open circuit) until the brake pin provides voltage. I've messed...

Done some more checks - got the bench power supply out and tested from trailer plug to rear and its all okay from there (testing one at a time). I wired up the car pins to the trailer pins with some croc clips - focusing on just the earth, tail light (RH and LH are bonded so only need RH) and...

Will do - I've cleaned up a few in my time, normally rusted to hell. A bit of filing, clamping the ground plate and bending the tabs up normally sorts it all. I've noticed you can buy all in one LED clusters now, instead of just retrofitting LED bulbs into the housing with is most often the...

iring loom is a Daxra one so not custom wired so shouldn't be wrong - because of the multimeter showing good I haven't actually checked this through yet - bit dark now but will confirm next. Bulbs are 380 type. Standard 7 pin socket. Indicator/Fog working to me shows earth is fine at least to...

I've been having problems with the lights on a small trailer - other trailers work fine so my socket is okay. Indicators and fog work fine. Bulbs tested with 12v work on both contacts, for side and brakes and side+brake together being respectively brighter or dimmer. The contacts are all clean...

I will give that a try when I can. But I am not sure it will do much different than running it at another property which has a mix of both types installed. Thanks for all the replies so far - will take me a day or so before I can test it in situ.

Yes, in its intended position its working with a low powered bulb. Although when testing on another circuit (Basically a plug into a standard socket) with the lights and etc off it does the same. Same when its used in another house, this house also uses low energy bulbs in some rooms but has...

I don't think the model of fan matters as the problem occurs even when the fan isn't wired up (I can use the status light to see what the controller is doing).

No earth...

The item was purchased online. It still comes on when switched live is disconnected...

There are multiple model numbers depending on what it does, Timer, Humidity, Photosensor and Infrared etc This is the model... (although picture is different). http://www.ventilation-system.com/cat/242/ It is possible that both are faulty, although I wanted to check with more people...

I have a Vents TH1.5N, its a fan controller that has a run on timer and humidity sensor. It works, with regards to time and humidity as expected. But what happens is whenever another item in the house, no matter which circuit is turned on, the controller starts the fan. This was...

All the Ryobi One+ batteries look clip on to me, are there 2 types? If you can see in my picture above, the battery I have is slide on - I cant find any example of a slide on battery for any ryobi type at all. I did consider replacing the cells, although its an odd nicad size and I...

Anyone know where you can get one? I cant even find a similar one by searching for it, not even other images of it - so I had to take one of my own... Image: http://bayimg.com/KAooeaadF