Search results

Yes, thanks, I'll check it out.

Looks like you have fairly deep joists enough for these. I wonder what the consensus is on these woven glass fibre hats: Saxby FH150 Small Heatguard for Recessed Downlights https://tinyurl.com/4a5ypzbw

Rocky, I think you’re on to something there. The one second to last on the right looks a lot like the one in my photos. I bet it’s a Varilight grid. I compared my grid photo to the Varilight VL GRID2 and they are a bit different, but it could be that they changed the design a bit. I’ll probably...

That sir, is very true.

Both good suggestions, probably what I’ll end up doing : - )

Hi guys, thanks. The dimmer is fine it’s just the actual rocker switch that’s physically been damaged since these photos were taken. I have no clue as to how it was damaged as the steel grid plate that it’s mounted on is pretty sturdy. Just thought someone might recognise if it’s BG, MK...

Hi All Does anyone happen recognise the make of the grid and grid/switch/dimmer modules? Apparently the switch is busted and I’m miles away, so thought I’d buy spares on route as I need to sort it. If not I’ll have to investigate then take a second trip return to the job. Cheers

As a metter of interest, was the guy who did the work a member of a certification scheme like NICIEC? Did he say he added a new circuit to your relatively new CU? If he did, did he add a new MCB, RCBO or whatever to your CU? If he did he'd probably have shown it to you before he left. I do...

OK, well if the kitchen tap has good pressure then I would have thought that something between the boiler and the hot bath tap is the issue causing the restriction of flow. The way I see it, looks like either you or a heating engineer/plumber need to find the restriction. It could well be that...

True that.

Sounds like a Rab C. Nesbit line :-) True though, give me washer taps any day. I've lost count of the ceramic ones that have worn out on me. But back to the topic, I'm presuming the cleaning you've done has stopped the bath tap whistling, so good news! Re the hot tap on the sink, I would have...

“the other tap was also whistling” – OK so it’s possible that both taps might be susceptible to whistling for reasons unknown. Putting that aside for a minute, it seems from the video that the flow rate isn’t that rapid. I’m guessing the hot water is from a hot water cylinder and not a combi...

Hi Alex, I looked at your other thread and it seems you’ve already done a swap check with another tap to no avail. Not sure if the other tap was a known good one (a non-whistler) but if it was, it seems the issue may be elsewhere. Does this tap have an isolating valve just before the tap, or...

Not sure if Tomsim knows if the dimmer causing the issue is compatible, but if he tests using a Varilight V-Pro LED (FYI, I'm nothing to do with the company), he can change the modes on it (leading edge, trailing edge etc) until he has a result that doesn't oscillate/flicker. He can then buy a...

I'd buy another dimmer to swap in and test with. Best case, you identify what the culprit is, worst case you have a decent spare dimmer.

I understand that some dimmers need a minimum load to work smoothly and flicker free. So , you might find a certain dimmer flickers with one 8W LED bulb, but if you drive say 4 of them in parallel it might run smoothly. Also, to follow on from what Eric was saying about types of LED dimmers...

We very much are Frodo. Your post 13 was an exelant presis of the kit etc. Also, a cable tester is essential as you say - also cheap as chips. Actually, if Deano is buying the patch cables, everything else is just the punchdown tool, so might not even need an RJ45 crimper.

Dean, all the above is good advice, but hope you haven’t been scared off by it. The loft does seem like the logical place for your main (and possibly only) switch as the cable layout for your size installation would be like a star, with the switch in the centre and cables to PC’s, cameras etc...

I'm guessing you're just demonstrating that it can be done without a router. I'm also guessing that your usual setup is using a router (or some other box) to provide a Firewall in addition to the the one included wither your OS?

Thanks catlad. OSB yeah, I’ll probably end up doing something like that. I know it’s more pricey, but I was also toying with using 15mm ply to keep the weight down.