Search results

  1. I

    Main Circuit breaker tripped

    Thanks. Will look tomorrow.
  2. I

    Main Circuit breaker tripped

    Ok Just I case your not around tomorrow when I reply as your put most of the day please advise the outcome. With reds separated it still does it. With reds separated it’s now fine. Thanks for your time.
  3. I

    Main Circuit breaker tripped

    Try as above. You mean separate the 2 red wires
  4. I

    Main Circuit breaker tripped

    Regarding post 10 here is the main consumer unit. The last one on the right was I believe in the middle position. I’m sure I moved it down then all the way up to the position you see now. I didn’t touch anything else.
  5. I

    Main Circuit breaker tripped

    With regards post 8 yes this one in the off position makes it trip. This is why I have left it in the off position. In the morning when it’s light I will remove the 2 red wires from the switch & separate them & advise what happens.
  6. I

    Main Circuit breaker tripped

    This consumer unit is an addition to my main in in the house. All electric now on when this light breaker is off. Previously when I switched it back on main would trip again.
  7. I

    Main Circuit breaker tripped

    As requested thanks.
  8. I

    Main Circuit breaker tripped

    There is no button. It’s just a on / off item. When you say separating do you mean remove light switch. 1 red wire in 1 choc bloc block & then the other 2 in there own choc block. Please advise thanks. Also advise what I mentioned about earth wire.
  9. I

    Main Circuit breaker tripped

    As per title main circuit breaker tripped. I reset it at main consumer unit but same again. I switched off each individual breaker if that’s what you call it. I then switched on each 1 at a time until it tripped again. I have now electric on apart from the lighting in my spare room so this...
  10. I

    Mower cable replacement & set up from scratch

    That’s what I mean. When ticking over it’s not even close
  11. I

    Mower cable replacement & set up from scratch

    That screw will make no difference as the lever that touches it isnt even close when its running. I bent back the lever of which the spring that was missing connectrs too. It now runs a lot better thanks.
  12. I

    Mower cable replacement & set up from scratch

    I assume you mean this one. Job for tomorrow.
  13. I

    Mower cable replacement & set up from scratch

    So this is the outcome this morning. Throttle lever right up in hare. Pushed left all the way to the left so choke closes as much as it can. Clamp up the cable. Fit new spring to top of carb. As I operate throttle lever & watch choke butterfly With throttle lever right up on Hare I see...
  14. I

    Mower cable replacement & set up from scratch

    Lever all the way to the left & this is how far the choke butterfly moves. This is its full travel / position.
  15. I

    Mower cable replacement & set up from scratch

    I seem to move it as far left as i can but its knowing where the outer cable is supposed to be. I then do up the screw & it seems to go to position in video
  16. I

    Mower cable replacement & set up from scratch

    I drilled another hole to move throttle lever down the handle a touch to give me more at carb end. So you say not enough do i just need to move outer casing left or right or do i need to start again
  17. I

    Mower cable replacement & set up from scratch

    This is the best i can get it, What do you think, This is choke only. When i operate throttle lever there is no movement on the part linked to throttle butterfly on top carb. Is that because i havent installed the spring OR because engine isnt running as i see there is a linkage from it to...
  18. I

    Mower cable replacement & set up from scratch

    So as you have seen that the choke comes on after full throttle would I be correct to say & do the following. Throttle Lever at Hare. Move lever so choke flaps comes into play. Clamp cable up. Then when using the mower have the throttle lever right back to Hare thus choke now on. Run...
  19. I

    Mower cable replacement & set up from scratch

    Ok then clamp Clamp cable up.
Back
Top