Search results

Hi, Just an update. Having decided to give it go, I have removed the panel in question and managed to gain access to the fan motor and removed it. Just ordered a replacement. Thanks, Benny.

Incidentally this is an image of the back of the oven. [/img]

We have a Creda Eoropa Solar Plus Model 48141, (circa 1995) and the oven’s fan has stopped rotating. Of late there has been a delay in its starting after the oven has been switched on but yesterday it stopped in the middle of cooking the Sunday lunch. The heating element continues to generate...

I currently have a patio door measuring 8’x 8’ (Approx) which has been in place for some 30 years. It was an Everest Aluminium framed installation (one fixed one sliding unit) with a small glass gap. It is still in good condition. Given the ever increasing energy costs I am conscious of the...

Everything went to plan. :D :D Room stat working fine with factory settings. Haven't had a chance to look at the advanced options, probably best left at default. A special thank you to D_Hailsham, without his help I couldn't have sorted this lot. Kind regards, Benny.

D_Hailsham; Thats fantastic;your a star. I'm off to the local merchants in the morning to get the DT90e. I was waiting for confirmation of its suitability given my wiring arrangement. Will post on progress. Once again many thanks and regards, Benny.

It appears to be some form of hybrid!!! Terminal 1 of the programmer is linked to terminal 1 of the terminal block. T2 Prog to T2 Block and so on to T8. Terminal block positions 9, 10 & 11 are hot linked to the programmer. Thanks you once more. Regards, Benny.

This is my system wiring connections; Is this sufficient to for you to make a judgement. Regards, Benny.

This is the Programmer switch. Is it possible the wiring of T603a was not modified in line the Field Replacement document (Attached above) when the old Valve V6057A was replaced with the V4043H at the same time as the boiler change out all those years ago? I found this document with the...

Just to clarify; the initial readings were taken across the terminals at the 'stat end' with the actual 'stat head' removed and not at the termination box. The readings you requested are; G/Y to Blue - Min. = 0 Volts. BR to BL - Min. = 240 Volts. G/Y to Blue - Max. = 0 Volts. BR to BL -...

Just sorted the ABV and now that aspect of the system is working fine. Thanks for all the assistance. I am now looking at replacing the old room stat with something where the wiring is similar to the existing Honeywell T603A so that installation would be relatively straightforward. With no...

That fantastic, thank you so much. I hope to get it sorted this week. Will probably need help with the wiring changes for the programmer/stat change-out. Regards, Benny.

It’s currently set at 45 Degrees. Enquiring from a local merchant I can get one of these. http://www.honeywelluk.com/Products/Valves/Bypass-Valves/DU145/ for about £15. As I have to modify the pipework anyway, the fact that it is an angle rather than straight shouldn’t matter. Hope to get...

As you can gather from the system description and the various niggle I am experiencing, this setup is currently on life support. I am just nursing it along for the moment as I plan to replace the whole thing in about two years. The layout of my kitchen units will have to be altered as the...

While the original system was installed many years ago (probably thirty) a new boiler (Baxi solo RS2) was fitted about eighteen years ago and this device was fitted at the same time. As for the device currently fitted; under normal operation how should this device operate? I would expect it...

Is this the type of thing; http://www.screwfix.com/p/honeywell-straight-auto-bypass-valve-22mm/34127?cm_mmc=Google-_-Keywordless%20Ads%20|%20Generic-_-HVK%20|%20Keywordless%20Ads%20|%20Broad-_-_cat:heating%20&%20plumbing&gclid=CPHW-KKt8qkCFYUY4Qod2252Wg Once again I am indebted to you for...

When it's set 'along the pipe' the water feeds through the valves but also back, via this device, to the return, with the return considerably hotter than the valve feed. When set across the priority goes to the valve feed. This is the pipe run; boiler to Airjec (this also has a feed from the...

Once again thanks for your help. I hope the attached provides sufficient detail. If you need clearer images I can use a better camera but then that will increase the size of he attachment. This is my first attempt at uploading on this site so I hope it works. Regards, Benny...

I have now fitted the replacement motorised Valve and the system functions correctly except for one issue. My set up has a non-return valve located in a loop (Tee junction) that goes from the section between the pump and the zone valves and the return to the boiler (again Tee Junction) after...

Unfortunately mine does not have the 'C' suffix, therefore its a Honeywell replacement and all the extra work. Such is life. Off now to order one on line (Plumnation appear to be the most competitive). All of your help greatly appreciated. Regards, Benny.