Search results

Nothing to do with battery, sounds like it’s a loss of signal whereas the siren is too far from panel, when the bell cannot see panel it thinks it’s under attack and will self activate, same on hardwired bells if someone cuts the cable the siren will trigger. Swap the front and rear bells & see...

Texecom Connect App is Free!

All alarms must be maintained annually wireless systems more so due to the reliance on batteries. The idea of changing the batteries yearly is to prevent you having any battery faults occur at 2am or false alarms whist out. The costs you have been quoted sounds correct (my firm charges nearly...

No company is going to give out their engineer code, if you have the enginner code and decide to play with the systems programming then disable something by mistake, the maintanting company could be held accountable if the alarm did not activate.

Yes a Manager PIN then User PIN, however no mattter what PIN you have it’s not going to reset without an Anti-code Reset. The code that is generated on your display currently needs to be decoded by software running the correct algorithm. I would get your independed company to reset it & change...

Press and hold D - you must see “enter security code” then 2000. Backlight option will be in that menu.

Press and hold ‘D’ enter security code 2000 press No to each question until you see “backlight” press D or B to toggle the [0] to a [1] (might be the other way) Once finished press ‘A’ to escape. The blue LEDs used by Pyronix are poor quality and eventually die or go very dull, this is why...

Go to Volume Control in engineers menu. I always set these to: A Exit 2 B Exit 2 A Entry 2 B Exit 1 Tamper 2 Day alarm 2 Chime 2

I’ve only ever done about two of these as panic button. Pretty sure you learn it then find that the Panic button option does not display. Then it’s found in the Manger menu. Try making the Fob user 90-100 from memory I had to enroll it to a high number, it may be that the Panic facility is only...

I think the option is only given in the engineer menu.

When you press ‘part’ can you then use the down arrow to view the other part sets?

Could you enable Quick arm? Neighbour will then press the “Part” (man in house) button. This wil then part arm for you. Pets must be under around 30kg for most Pet PIRs.

Yeah it would... but you don’t have too, you should get 10 individual cores into each terminal. Strip them all back & twist tightly together then snip off the rough & you should be left with a single solid core as such which should fit nicely into the individual power terminal, do the same for...

Ok it sounds like you have no electricity going to the panel, check electrical fused spur first then check electrical fuse inside panel. A volt stick or mutimeter will help.

Depending on type of keypad/software the flashing light means different things. Does it say power next to the flashing LED? If so you have no electricity going to the alarm panel hence the battery is now running low.

It may be that the battery ran low during the power outage, it’s rechargable so the system will recharge it once power is restored. Once the battery is fully charged you should be able to reset the system by code/fob yes/no. Sounds like power may still be off for the alarm, is there a power...

Sounds like a castle/Pyronix Panel. The battery is inside the big metal box, make sure you have electricity going to the panel first. If you need to open the box ideally you need to put the system into engineer mode, or just open the lid (internal alarm will sound) silence with code, replace...

You can wire a 16ohm cone speaker off a hardwired remote keypad (if you have one?) between + and OP this will mimic and enhance all the tones made from the Enforcer panel. Or you could wire a siren for alarm tones only from the Enforcer panel (small circuit board on bottom right.)

I’m not that knowledgable of the wireless arming station as it’s so new. I doubt your be able to enable any backlights as it will be due to saving battery life. Holding D 2000 takes you into that specific keypads internal programming only. All global programming is done in the normal...

Press A