Search results

It will work the same if direct coupled, the wave power devices often not direct coupled, connects through an inverter.

Seems to be working well, copied what was done at the heritage railway where I volunteer.

The generator needs to be directly connected to the grid, not through any inverter, so it depends on how many poles on the generator, looking at 6000 rpm, 3000 rpm, etc.

Have chicken wire over mine.

Since when has politics made sense? The big problem is lack of rotating mass. With an alternator connected to a large steam turbine, a sudden load will be taken up by the weight of the rotating mass, but with wind farms, solar and wave power, there is an inverter between the rotating mass if...

to 1 and 3 and N and L to .

It is called a motorised valve, it has a micro switch inside, so the boiler will only run after it has opened. I have tried reading the description, but can't work out if valve at fault, or what supplies the valve (thermostat and programmer) what tools do you have to test with?

I volunteer to work in a large unit with only limited 230 volt outlets, so cordless is far less hassle running out leads, but in the main @opps is correct, drills, grinders, saws, etc, good reason for cordless, but router is not normally used when no 230 volt power. They don't tend to be used...

Yes, so now the big question, if I have used a 2 Ah battery before starting my gardening, so left with an odd number (1 or 3) 2 Ah batteries charged, can I use the 4 Ah while waiting for the 2 Ah to recharge? What happens if I put a 2 Ah and 4 Ah battery in the same garden tool? Can't believe...

I had a Main 7 instant hot water boiler in the last house, it only did DHW, there was another boiler for central heating, seem to remember 18 kW, which was ample for the DHW supply, and we draw DHW for such a short time, turning off central heating when we want DHW is not really a problem. So...

This is a very difficult subject. I had been told for years, cheaper to heat DHW with gas to electric, and I never questioned it. In the main as near impossible to measure, the gas boiler could modulate, so run times tells you nothing, and the immersion heater was powered from a FCU so not easy...

Years ago I could get a plug from MANWEB which the line pin had the hole for the fuse so it only stuck out a very small amount from the wall, the insulators on the live pins resulted in their demise, but many of the moulded plugs also stick out less from the wall so washing machines and the like...

10% reduction of £100 = £90 and a further 10% = £81 not £80 seen this done a lot.

Yes, now need to use DERV or diesel engined road vehicle fuel for generators.

It is not the efficiency, it is the start-up and run down times. Connah's Quay combined power gas/steam turbines take around 48 hours to get to maximum and to stop again. Moving for 50% to 75% output quite quick, but 25% to 95% that's slow, as the gas turns the turbine, then the waste heat makes...

I don't know what thread it was pulled from, but I can see the problems with 150%, the first time I came across it, was running and engine on two fuels to calibrate the engine, and we then ran it with a fuel under test to see when knocking started, and quoted the percentage of Octane it was...

I am an electrician who worked with welders setting up pre-heating, and stress relief, and also repairing welding machines and welding with them just enough to test my repairs, I was taught how to weld with stick and gas, during my apprenticeship, but that was in the 70s, and not really don't...

There are TRV heads which can be remotely controlled, the Kasa for example can be controlled with sensors on the opposite wall, and so can Drayton Wiser. I fitted Energenie TRV heads, which monitor both water and air temperature so it can compensate for the direct heating from the radiator, but...

Once fitted, you will get notification if voltage out of range, but until that point you don't really know how often voltage will be out of range.

2 amps is not the same as 2 amp/hour. The Parkside 4 Ah Smart battery is limited in the software to 50 amps discharge current, so 1 kW which is likely well over the rating of the motor, but clearly not 2 amps by any stretch of the imagination.