Search results

Boiler runs for about 30n mins no problems then has issues with the flame knocking noise /nearly going out does it approx two times in the space of about 5 mins then no noise issues after that very strange. Only started happening last week or so apart from this no issues touch wood, spoke to...

Agile where did I say all RGI are out to rip people, grow up and get a life.

Agile don't jump to conclusions this board is for people identify maintenance issues so they don't get ripped off please do not be judge and jury.

The fan works ok the clicking noise is when the flame is impacted by which I assume is flame vitiation. I did notice that one of the rubber tubes (red) has become torn from the metal connectors and rings where present where they were torn had become visible so I assume some form of pressure...

Thanks, I thought this as well, I opened the boiler up today put there appeared not to be any corroded parts from the out side, also looked from the outside and put a torch down the flut put could see any signs of damage. Is there any way to check, is there any kits that baxi sell to resole the...

Hi I have a`Potterton Profile 80E boiler, about a week ago I noticed my boiler would make a clicking sound about 20 - 30 mins after start up it would make a clicking noise and when looking at the flame it looks as if it's going out. Now every day I start the boiler up the same thing happens...

I got the figure by using a btu to kwh formula. With regards to reply are you saying that my boiler is probably the near max for the rad's I have, also as the boiler stat is set to 3, the boiler stat is incorrectly configured?

I've estimated that my rads KWH = 15.220352958 (using Stelrad Elite Catalogue figures).

I have a potterton profile 80e I have 11 rads in total 8 of the are double skinned wth two large double skinned ones in reception rooms (the ones that only heat half way ). The boiler is about 10 - 15 years old the specs are: Manufacturer Potterton Model Profile 80e Fuel Type Gas...

Sorry typo I did leave x400 in for a month.and the flushed out system. So putting up the bolier themostat may resolve the issue with the collder last two rads which only heat half way? If I set the boiler to maxium output are there any issues / problems I may have? I have a room...

I checked the air vent with the water cup method and it appears no air is being sucked in. The rads that only heat half way are the furthest away from the pump and the largest I have flushed the system and tried to balance the system with x400 however this did not resolve the issue...

I'm confused the air does not appear to be coming from the air vent in the loft. I've had it tested and no air is coming down. There appear to no leaks anywhere. Just can't figure where the air may be coming from. Any ideas chaps?

Would filling the f/e tank with more water be an issue and the f/e tank is around half full at the moment?

is the air seperator I have, not very good?

The height is around 2 -3 metres, the air vent slopes up an over and bends in the f/e tank.

I dont think the cold feed is blocked as I drained down the f/e tank t and refilled a month ago when I changed punp and the pressure was ok when I opened pump vale. The height is around 2 -3 metres, the air vent slopes up an over and bends in the f/e tank.

muggles I think your right, then vent appears to be connected on the negative pressure side, what do you think guys. Thanks in advance. http://www.diynot.com/network/rrwfotr/albums/4702/18816 http://www.diynot.com/network/rrwfotr/albums/4702/18817

The pipework appears to be bog standard, the feed into the system is in the loft connected to the f/e tank. The vent is connented to the hot water cylinder and feed pipe below the f/e tank. directly below in the airing cubard. Just find it stange that setting one on pump appears to draw no...

I think the pipe work is ok just the pump is two strong on setting two for 15/60 pump. The reason why I added the bigger pump was that I have two rooms that have quite large double skinned rads and they only warm up half way the bottoms are cold so wanted a bigger pump to warm the bottoms...

Yep postioned pump in same postion as before. The air being drawn into system when placed on setting 2 on higher rated pumo 15/60 the previous punp 15/15 on setting two did not vent as much air I only bled the bathroom rad once every winter with the new pump it's needs bleeding every day :-(...