Search results

calpeda mxhn 204 with a clarke pressure swich set to 1.5 bar and a range 300l unvented seems to work fine with the cylinder 24l vessel can wash hands ect without he pump kicking in. seems to be alot more silent then the old shower pump. I am boosting the lot into the cylinder and spliting off...

just finished new bathroom with a wetroom shower, rigged up the system to a 45x45cm drench shower head, it's the best shower i've had, i have restricted it to 4 bar as the hand shower was uncontrolable it would fly off when switched on, ended up running a 40mm pipe from c.w.s.t to the pump and...

THANKS GUYS GOT IT WORKING NOW HOWEVER TWO OF THE PIR'S ADTR ONES SEEM NOT TO TRIGGER THE ALARM WHEN YOU DO A continuity TEST THEY WORK CLOSED THEN WHEN TRIGGERED OPEN CIRCUIT, NOTICED THAT THE TO HAVE A MUCH HIGHER RESISTANCE READING THEN THE REST, TRIED REPLACING THEM STILL NO JOY, IF I REMOVE...

hi i removed bell and shorted the T & A on panel with new battery works fine. When i connect bell up it goes into tamper again. opened adt bell housing the wire are as follows H+ red h- Black RTN Yellow R Blue Battery black on the panal i connected...

the same thing that protects my tails on the houshold cu, the main incoming fuse, there is a 100a dp switch in the first box supply the secound box which has a 80a rcd and a 60amcb

the 10m of 16mm is armoured and the cu 's are both MK metal types.

sorry when i touch them the siren does go off its hard to hear it as the garage is at the back and bell at the front. i have disconected all sensors, only wired in lcd panel including the tamper, have put a jumper in the other tamper and pa trminal bell is wired in and seems to be silent if i...

i did not use swa the sparky did, i'll explain full set up now. supply fuse, henley block to home cu and 100a isolator box, 10meter run with swa 16mm to a metal cu with a 80a rcd and 60 mcb. This is then run into a small 100a isolator box with a switch next to the boiler using the h07 then h07...

yellow one thanks

thanks for that however the sounder is the original adt one can it be changed or shall i replace it.

Hi thanks for your reply got a link for the terminal http://www.weidmuller.co.uk/43534/Products/PCB-Components/PCB-Terminals/Up-to-25-mm-cross-section/LUP-Series/products.asp the original cable in was 16mm armoured however i could see that it was pulling at the board were it was so stiff...

when the two wires are apart the bell outside rings when there togeather it silinces them. thanks

hi thanks for your reply just posted pics of terminals as i was waiting forr new board to arrive the old one has had a treble by-pass operation to get it going will swapp them over this week. the terminals when screwed the back contact is pulled towards the front and the contacts are grooved...

can i by pass this to test buy utting a jumper in keypad, how do i override bell tamper, i think the fualt is with the bell box as changed this panel becuase adt one was coming up with a tamper. bell rings when you disconnect battery do the other two wires work like a switch i.e open or closed...

just bought a accenta min to replace my adt galaxy panel. wired it all in and it keeps coming up with tamper locked out so i have taken all the sensors and bell off, put a jumper in the two tamper terminals and pa terminal i have powered down and it still has same error, also door contact is...

still waiting for a ticket from him, basicly his not coming back, supply head was not labelled when i asked him at the time he told me it was 100a, there was a hemley block already on the wall so he tailed in a 100a dp isolator and run the 16mm armoured into it which then ran 10m along the wall...

hi thanks for all the advice went down to the local lecy suppiers i use he is a electrician as well worked out that the cu prevous spark put in was fine with 16mm armoured, Obviously thats were it ended with him, so supplied me with 60a mcb and 100a dp switch and box to mount directly above...