Search results

cheers

Cheers denso, got spare tiles, big ones, so smashing the in situ one will be the only way, pipes channelled up the wall for both pipes, not a lots of wriggle room.not what I would like as a last resort, which it may be! Gonna let it run till it packs up completely then will decide what to do...

This is one of few sites that says available??

Hi Warner’s, shower doc also says discontinued, no other available, so looks like a new one, if I can find out how to adjust pipe work inlets?

Hi Denso, if I cannot get new valve, any idea how I alter pipe work from 125mm to 150mm, without smashing tiles etc,to fit a new one?

83315530.part number?? Sorry but not posting very successful.

This is screen shot of national shower spares, not available, discontinued!??83315530 But available on some sites??, but no good if cannot get old one out.will try wd40! Cheers. Used daily

Thanks both, much appreciated. I’ve posted it on shower doc, today. I googled it, and results vary, but most say it’s a generic one for multiple models, but triton, and SSP say it’s discontinued, no alternative available, but the part number is available on some sites?

Hi guys, a bit of advice would be much appreciated. My shower control, triton? Is starting to play up, not closing properly and leaking. Having to force it shut. It is 28 years old, so been a good- un! I don’t know the model, and was under the impression it is ceramic cartridge? However, I...

Cheers exedon, realised that when I posted , flow rate. What’s the cone I read on posts? Is it where the diaphragm hits against to stop inlet ? It’s the ball type. Changed downstairs to dual flush few years ago, but it packed altogether. Cheers

Reckon you are probably right. Just tried turning the stopcock down to the whole house, still the same. Cheers

Hi guys, appreciate a bit of advice please. My upstairs toilet cystern, for some reason, the last year or so has been making a noise, vibration, when just at the end of filling. Just a few seconds till it finally stops water coming in ? I know it’s the inlet valve diaphragm, BUT, I have changed...

Hi D . Thanks for reply. what openings ? cannot find anywhere water ingress to cause it! the wet you can see is water running paint on top of wall,down off coping, hence putting new drip strip on.plus Ali tape on top joints. as this photo shows you. will try anything , it’s a pain. do you mean...

The whole house is normal render with no problems, so assume it is just bad render. the two small walls of my conservatory, which was built and rendered when wall was done, the top coat of render came off as I pulled the weathershield off. the top coat render was soaked under the paint ? scratch...

Thanks conny, done all of that over the years, except leaving it bare, during summer, for a long spell, did it last year after we had the long heat wave. it only takes one shower and it’s wet again,so do it when nice and dry , weather unpredictable hear. wall is sound . as you can see, it is...

Hi Robin. yes, put aluminium tape on joints, to see if it helps. that was last year, so didn’t help ! yesterday, put felt strips on edges to form a drip strip , siliconed them and screwed on,as coping only sticks out 20 mil, ish ! wondered if water was going behind render.

Hi guys, would appreciate advice please. as you can see, my exterior wall keeps blistering and have to scrape it off every year. always used deluxe weathersield. usually late on when weather goes colder. wall is circa 16 years old. rest of house ok, just this new part ? any advice welcome...

Thanks Ian , much appreciated . Never thought of that.

Cheers Ian. On the Trv , the fitting on the pipe is not a standard compression, 15 mil, so, presume will have to cut the pipe below it and use a new one, if there is enough pipe to pull up from below floor ? Cannot just change the body of a new one ? Got three like that leaking ! When closed...

Hi guys, can anyone tell me what type of Trv this is. The fitting on inlet isn’t coned, it’s Leaking on pin when closed. Lockshield on other side same, but should be straight swap? Is it 15 MM to 1/2 inch ? Only ones I seem to be find ! Looks like 15 mil to 20 mil ? Like using imperial still ...