Search results

Aftermath of someone elses "care", pictures... Saved low pressure piston. LP side of crank is also fine, no scratches/grooves. And surprisingly cyllinder inserts/liners are absolutely pristine, both of them. If not for the chip at the bottom of HP liner, cyllinder block would have been ok as...

3 phase is nothing. Just replace electrics with 1ph - done. Simples... If it only were that simple :D

Well you wouldnt normally run an expensive sort of compressor like this. New B70 units come at about 1k plus quid. Just for the pump itself... It pains me to see things like this... Even if i find part supplier in all probability it will be expensive to fix. Hence writeoff, as i cannot afford to...

They have a tool shop in Dungannon, close to me, but to my knowledge they only sell tools, no service. Will have to call them up on monday, but i dont have high hopes.

Sadly, i have to report that compressor is a write off. Taken off compressor unit, disassembled it. 1. One of the pistons, connecrting rod and rings are in bits (smaller one, high pressure ?); 2. Broken pistons crank shaft side torn to shreds; 3. Cyllinder liner chipped on the bottom. 4...

Got the puller... And here's the first hurdle - the wheel is so seized on i'm afraid to break it. Puller damaged some of the fan blades on it, but no biggie, however after considerable effort and heating and loads of wd40 it didnt move a millimeter... Rechecked it for setscrews, just in case...

Oh dang it. Any ideas how to pull the wheel off the shaft ? Pullers i find here are not big enough. Inner hub diameter is 140mm, thickness about 45mm. Not keen on banging on the shaft...

The pressure switch is going one way or the other - its for 3ph. I would love to test the tank hydrostatically, yeah, but cant find anyone local. Thats the one expense i would justify, tbh.

I will be flushing it anyway, then inspect it with endoscope. Need to figure out how to undo 65mm bung... Compressor in question:

I'm working on a budget of zero. Just spent figton of money on laser cutter, wife's gonna have a fit if i spend anymore... So, whole kurust/redox/hammerite treatment might not fly as too expensive. Wirebrush+paint direct to steel works ? Or do i absolutely have to primer it ? Paint direct to...

Hello people. I've been given an old 200L compressor, with 2stage ABAC B70(B60?) air pump. Its been sat for a while, fins are dirty, no intake air filter box, but other than that it got all the bits attached. Except motor, left it where it was stored as it weighed 3/4 of the compressor+tank...

I'm planning on building myself a 72x2" belt sander. It seems the standard is pretty much american. Where to i get belts of this size in UK ? 50x1830mm ? Ebay doesnt seem to have any good selection ? Looking for a starter kit with most common grit grades (80-400 ?).

I'm thinking on building a deck over my messy back garden. Grass is massacred by ten ton front loader wheels (dont ask). No point digging it out as there's clay right under. Hence the deck. However, we here get some severe winds and i'm not confident its not gonna fly away one day in november...

Its a black&decker 339, a very small saw. just maneuvering the blade between the guides is a bit of a fiddly job.

Not spoked, solid. Thats actually a great idea. I might make some holes in the wheels, drilling symmetrically for balance i'd assume. Hm...

Oh. My. God. I nearly punched a wall just now. Typing this here just to calm down. I have a small hobby bandsaw, three wheeled. For the past hour i have been trying to replace the blade, put a new one. Not the first time but this time its just made me go berserk. I'm fairly hard to anger, but...

Hello folks. So, today my boiler decided to paint my house end black. Went in with a wrench, scooped out loads of rubbish, rust and whole lot what appears to be internal insulation. Boiler is completely rotten/rusted etc... Firebird Popular 90 and MonoFlame Minor 1BR ST burner. Took off...

I bought a commercial treadmill, as faulty. Paid peanuts for it. Hope to resurrect it to former glory. Is it considered an appliance ? :D (If it is) Its a LifeFitness 9500HR Next Generation (RT9500) commercial treadmill. When powered on i can hear hum of transformer, motherboard lights up...

Its one thing to say "you'll let magic smoke out" and another to say that AND explain why it might happen. I'm not one of the "is it even plugged in" types. Former IT guy, mess about soldering bits and pieces, fixing some simple things etc. Never had to deal with charging though...

So explain it to me without being a dick. Or dont.