Search results

Washer dryers can be less efficient with respect to drying. The inner drum on a washer is smaller than a dryer drum. Therefore the space in which the air circulates around the clothes is smaller, thus a smaller load is dried in the same time in a washer dryer. Furthermore a washer drum...

Open the door hold fast freeze close the door switch with your other hand release fast freeze release fast freeze enters into the next diagnostic level on some models each step is moved on with one of the function buttons The last fault The software version The display fully populates step 4...

With respect to the hob. It depends if the manufacturer permits. The instructions will detail wether a rigid, flexi or both are suitable

If you are are able to test the defrost thermistor (white bullet which clips onto the top of the evaporator)may be wrapped in foil. By unplugging the connection from the pcb.. in the top console ..usually two thin red blue or black blue wires you should measure 20 odd thousand ohms...

Usually the wires would be live on the rleft earth to the plate which screws to the cabinet and neutral on the right, when viewing this from the front. Most suppressors had internally connected wires from the mains lead with a rast style plug fitting into the top carrying the current to the main...

If the drain hose connects under your kitchen or utility sink, make sure the hose goes down onto the spigot. If its horizontal or points up, you nay find the water is siphoning back to the dishwasher or water from the sink could back up near the u bend and end up in the base of the diswasher...

The float / pump chamber can block up with wet fluff and unused detergent polymer, especially if you run regular fast wash cycles in your washing machine. You can easily remove the float cover by inserting a flat blade screw driver into the clips which fit into the back plate and ease them to...

Sounds like the motor triac shorting perhaps. What happens if you run a rinse program? You should find the machine fills and the motor turns the drum

Take out the freezer drawers. Turn off the appliance. Re move the screws on the rear panel. Some are recessed. Lift the rear panel off lifting up and out from the bottom to avoid breaking it. Remove the fan assy by prizing out each of the clips. You may find a large ice formation under the...

Sorry just noticed the model on your post. Best to contact Bosch. There was a recent media campaign regardinga pcb fault. Most were over 10 years old.

Could be the heater relay on the pcb. How old and what model is it?

Check the corrugated plastic hose which runs from the metering tank to the sum for blockages. You can remove this easily from the metering tank end by removing the lhs panel. The sump end is accessed by removing the metal plate at the front behind the door above the base unit. Two screwd...

There may be a short across the switch. The live comes from the double wire which locates on position 3. The switch in the switched position alows the live to run to the timer card. Normally the live loops to the heater relay contact on the timer. Try disconnecting the double wire from the...

Use a white board. A large piece of thin hard plastic. Slip it under the front of the appliance by lifting it just enough to slide under. Now tilt the appliance towards you and drag it backwards. Check after a few inches that the gas hose or electrical supply aren't too short.

Does the oven have other elements? A grill or base element would be added to the total draw on the rating plate. If the element secures to the oven and the fan blades dont catch the oven would take a bit longer to heat up with a lower wattage element.

Looks like the air break unit is blocking up. When it pumps out the water runs up the air break and then down to the outlet hose. I used to see this on earlier models. If it blocks with food soilage it can reduce the flow. I think the two hoses at the bottom left look like the outlet hoses...

* trickling out of the arms

The wash motor is the lively cause. If you open the door just after it has finished filling and started washing you should see lots of spray and both arms slowing down. If you don't see spary and water is only trickling out if the arms then the wash motor / pump is possibly not forcing the...

Check the wash heater terminals. The live supply should piggy-back off the heater to the module this may have snapped. Can you find a lonesome wire there?

Epoxy resin can work. Milliput can be bought at craft shops and some diy stores. Mix equa This will fix any holes smaller than a 5p piece. Inside the Milliput box is two tubes of plasticine. Mix equal amounts of each together for a minute or two. Then apply the mixture into the hole and...