Search results

One of the fans in our Samsung built in oven, screeches when switched on but quiets down when warmed up. Can I lubricate it to keep it going ? Has anybody tried oiling an oven fan ?

Gently turn the screw back and forth , gradually moving further to the off position. If it is stuck then you have to look at further upstream to turn a main stop cock off if the toilet is mains fed.

It may be the pump is too vigerous causing the whistling - particularly in TRVs. Don't know if you have settings on the pump like you have on pumps external to the boiler ?

Thanks all. I'll try to find the MK3190 or just use an ordinary switch. Basically I want to avoid the fan coming on every time someone pops in the bathroom. Also it avoids the three pole isolation switch which confuses everyone. Bathroom refit due next Jan by trade.

I have been looking for "momentary" or "retractive" pull switch but cannot find one? I have seen them in hospital bathrooms as alarm switches with a red cord. Any ideas ?

Instead of the usual bathroom fan control via the light switch, I want an independent switch to turn on a fan with timer. I envisage a momentary pull switch that kicks the fan into action; the fan then runs on its timer circuit. The momentary pull switch being one which only connects when being...

Yeah ! That's it. Thanks. Had a look at the element in the oven and it matches the picture in one of the spares listings. I'll do some measuring then order. Looks like the screws are accessed from the back on this model. Around £20-30.

I need a grill element for an Indesit single oven but can't find the model no. Any stickers on the front have long gone - hoping someone can advise by the photos attached. Otherwise have to take it out and look at the back. Thanks Dal

There is probably a management mark up !! For instance, renting agents charge for arranging a washing machine to be fixed, often more than the actual repair.

We just had a water meter fitted out in the pavement and the pvc valve out there is a quarter turn valve. I noticed our flow rate improved , probably because the new fittings are less restrictive. I wandered if I replaced my main stopcock whether that would improve the flow even more ? I was...

Amazing ! Just missed your update while I was typing !!

Has this been resolved ? Anyway we had a similar problem a few years back - basically a lack of flow. It turned out to be an innocently looking anti-gravity valve. This looks like a 22mm connector usually just above the pump but inside this is a little brass disc that stops convection in the CH...

Just a thought - do you have to have some flow for the PRV to work ? Is there a difference between static ( no flow) and flowing pressure. I.e. if you actually run the hot the PRV should do its job.

If you have a pump and a three way valve OR a pump and two valves then your system is fully pumped. Some older systems the HW side was gravity circulation (nothing to do with gravity fed) and you could not have separate CH times hence the option on the timer. Anyway what was your old timer set to ?

To undo it you have to move the toilet forward which involves disconnecting the cistern etc. Then you will see the size of the old toilet connector. You could just try twisting the existing connector in situ but it may make it worst. Does the pipe going out slope away ? - check with a spirit level.

I think the reason for checking the feed and expansion arrangement is that if you put the pump in the flow, it may pump water up into the expansion tank continuously.

It's me the OP ! The ridge/ripple caused pooling and trapped debris and moss. I cleared the moss etc and it's a bit better but still leaks. The leak is all along near the ridge but also appears further down at the next joint. I think the water seeps along under the felt. I will try fixing when...

My shed roof felt has expanded and pushed up a ridge right across. The edges were nailed down so could not move causing a ridge on expansion. Any suggestions on how to smooth out the felt ?

My son has a Vaillant Ecotec pro28 in the loft with a flue going up through the tiled roof. The boiler is one of the first of this model dated 2006 so is due for replacement. Could the current model of the Vaillant Ecotec be installed to use the existing flue. The boiler is on a flat wall...

You could bypass the dvd altogether. Get a VCR and a digital converter which will convert the video to digital files on your PC. This type of gadget are also called a video grabber. You can then copy and email the files to your heart's content.