Search results

Everything looked fine on the boards.. there was no rust or "chalking"/white powered anywhere but I will go with it and see how long it lasts. For anyone interested Miele do a £289 fixed price repair.. but didn't check if they would cover my machine as usually they cover stuff from 15 years ago.

Some good news... I am not sure what happened but I put the machine back together today after taking it apart to check the 3 circuit boards on front panel and thought why not try the machine again... and it now works!. I did an empty rinse cycle and it worked without any errors. So I did a...

I get the flashing red light "Water inlet/drain indicator" when I put on a wash or rinse cycle, after it fills the drawer for a few mins/i can see the water coming in and hear the drain pump going - letting the water out the drain hose. Is that not the error message??

Here is better versions of the circuit board CAD drawings if they are helpful - managed to digout an old scanner instead of using the phone to take pics https://ibb.co/h1F8hpWM https://ibb.co/XkShDjNc https://ibb.co/9H9x2sBY https://ibb.co/SwQpQ6YL I thought that if the relay was stuck in...

There is only one pipe that goes to the drum from the drawer and it is connecting up fine and with no blockages Darn, I forgot to do that test before taking the controller boards apart. Will put everything back together and try that, most likely tomorrow now. Feeling a bit under the weather...

There is a secondary board (EFL900) that has 3 orange and black with connects to the mainboard (EPW900). The reason I thought relay for the pump might be elsewhere is that in there is mention of M8 (drain relay) in both the diagrams and in one of the diagrams it looks there is a 2 pin/wire...

Thanks and woohoo.. I managed to get knobs then board out!. It all looks fine to my eyes. However I found some circuit board diagrams in wallet attached to the inside of the machine. I am wondering whether the drain pump relay is not on the mainboard out elsewhere on the machine with a wire from...

Has anyone removed the pcb board on a miele before? I am struggling to remove it and the front knobs too. I tried putting a flat screwdriver in the gap behind the knobs the pulling on them but they are not coming off.. I don't want to snap them off or break them. Is there any tricks or correct...

Thanks.. will look into the cost of a repair via Miele. If it is more cost effective to just get a new machine. I don't have or want to spend the big bucks to buy another miele despite the many long years of service this one has given. I used to also go with Bosch machines previously but it...

The machine seems to be working as normal as it should be when spinning just after the spinning is finished the pump keeps going despite the cycle has finished

forgot to mention that it works fine when spinning.. in spin mode, just pump starts when it has finished spinning and keeps going/pumping

Thank you... I will try disconnecting the pump as you suggested. Is this PCB - EPW 900 - which I would possibly need to change? it looks complete, no requiring any soldering or such.. just putting in some plugs/connectors Thank you

yes i have, the drain pump is constantly running. I did hear click before the pump started running near the bottom of the machine when I reset/tried resetting the machine (removing the power for 10 mins and then powering it back in)

How easy it is check the control board or is it just a case of getting another control board and try changing it to see if works with another control board? Is the control board easy to change/replace or should i just cut my losses now and get myself a new machine? If so, what brands are good...

how to i look into this, is it an easy thing to check, fix or replace.. or is it time to look at buying a new machine now? Thank you

The bottom of the machine looks and feels dry. I did tip is back and nothing came out - tipped it back at about 30 or so degrees The only time the drain pump is not on/running is if I put it on a drain cycle, then the machine works as it should, it drains and finishes without any errors and no...

Tip in either direction? Is the anti-flood switch at the front or back of the machine usually? Thank you

I googled miele wt945 water drain valve - only comes up with the triple inlet valve.. and the other part i found is the pump. Which given that it is pumping water out fine surely isn't faulty??

where is that located on the washing machine please?

Hi all, I am having issues with my Miele wt945. There is no water going into the drum. I can hear and see water going into the detergent dispenser drawer and can also hear the water being constantly being drained/pumped out. I have cleaned out the filters (fluff filters, water filters)and even...