Search results

That's exactly what seemed to have happened. I've reversed it and all is working ok now. Thanks for your assistance!

It still showed as the initial image. I went into rkp and removed Zone2 from rkp1, and the zone4 went back to normal.

Looking at rpk's I suspect somehow zone four has attached to rkp1 Zone2

I removed the tamper loop altogether and just put a piece of wire on the panel, same error.

Hi all, I setup a premier elite 48 some months ago, working without issues. It replaced an old system so wiring wasn't changed to sensors but was checked for continuity. Zone 4 has suddenly come back with a tamper error. I've removed the wires on the panel and checked continuity which reads...

Defo getting someone in - just wanted to understand the options. I guess I can get them to adjust and secure the telescopic part at the same time!

So I gave it a gentle tug yesterday - it has movement of approx 10cm, so i guess that is the telescopic part... Looks like i need to get someone in to extend the flue

Hi, I have an intergas hre boiler installed with an intergas horizontal telescopic offset flue kit. The outide wall where the flue is currently will be coming into a leanto. I wanted to know if the telescopic flue is adjustable in length to clear the lean-to (ie is it just pull on the outside a...

Thanks! Now to find a brick layer willing to do the job!

sketchup drawing... does it work? (Noth sure if the pillars are thick enough two blocks of 140mm? Expansion gap to the left of every second pillar.

What software did you use to create that image? Looks like your suggesting 11 pillars an 5 blocks between with one end being 6 blocks?

Also, I was looking to build the pillars using the method in this video: But that wont work as the blocks I am looking to use will be 140 wide, not 100 wide (so two blocks on the side will end up 300 not 200!) Block size I am looking to use are: 440x215x140 What other methods would work for...

No plans for rebar/re-enforcement, the wall will be behind a gate so not expecting many people of that nature to give it a go. Most likely damage would be from a vehicle who has mis-directed their aim, in which case i'd guess i would want the wall to fall away in that section rather then leave...

Thanks @PaulJR So if i go with 6 pillars total, 9 blocks between pillars, and have expansion on each pillar on both sides? or tie one side solid and let the other side expand? So I would have: Pillar|9 blocks + mortar| expansion| pillar| 9 blocks + mortar| expansion| pillar| 9 blocks +...

Thanks, so if do: Pillar|2.25m block| Pilar| 2.25m block | expansion|Pillar|2.25m block| Pilar| 2.25m block | expansion|Pillar|2.25m block| Pilar| 2.25m block | expansion and so on? Where the blocks on the left of the expansion are then not tied to the pillar on the right of the expansion or are...

Hi All, I am looking to have a 28m block wall built in place of fences (some of which are now neatly stacked up). I'm trying to understand the block layout, number of pillars and expansion joints that various people have told me I need! So the wall will be 2m high, 28m long, and stepping...

Thanks woody, To clarify, the garden slopes down from front to rear by approx 1 meter over approx 30m length. I'm looking to have each 3m section stepped to keep it approx 2m following the ground, - the intention will be in the future to have both sides roughly the same by reducing the height...

I appreciate this may have been done to death - nearly- but I just wanted to check before I go ahead.. I have a garden fence at present which is no longer standing due to Wind. In place of the fence I will be replacing it with a wall. Now the side where the wall will be going is the boundary...

I've got a tap like this: https://www.franke.com/gb/en/hs/expertise/special-features/franke-filterflow.html Normal Hot and Cold are softened ( the reason for cold softened is that you don't get the limescale build-up on sink, dishes etc when you mix for washing or any other reason to use cold...

Get an aquarium test kit like this: https://www.ntlabs.co.uk/browse-products/indoor/aquarium-lab/aquarium-lab-multi-test/ The KH and GH will give you the hardness! You can pick them up for approx £20 on amazon.