Search results

Thanks for clarifying this Dan. So I have a choice of the following two options then: 1) connecting receiver L to Terminal 1 and switching CH on for 24hrs on the programmer 2) connecting receiver L to Live on the Wiring Centre. CH setting on the programmer will be ignored in this case...

Hi steelmasons, You're right, two L's are connected internally. What I meant to write was connect right-hand L and A. So it will be like this: Wiring Centre 1 - to stat left hand L Wiring Centre 2 - to stat N Wiring Centre 3 - to stat B And link right hand L and A on the stat. So this...

Found a similar topic: //www.diynot.com/forums/viewtopic.php?t=221578 According to information there, Live and Neutral are also available at terminals 1 and 2 on the Wiring Centre. Which makes sense, because at the moment terminals 1 and 3 are linked by a wire that emulates a stat that is...

Hi Dan, Thanks for the quick response. Should I also link right hand L and A inside the BDR? Otherwise B will not get any current.

Hi, I want to install Honeywell CM927 thermostat (I don't currently have a room thermostat, only Landis&Gyr RWB200 programmer). As I understand it, I need to wire the Relay box BDR91 that comes with CM927 into my Honeywell Wiring Centre. Unfortunately, I can't find the wiring diagram for...

Hi, I'm considering buying my new floor from Jordans Wood Flooring Warehouse (http://www.jordanwoodfloors.co.uk/), but can't find any reviews or feedback on the internet. Has anyone used them? Any comments on the floor quality?

Thanks WoodYouLike, So do you think floating method is ok in this hallway? Do I need to do anything extra to fix planks on edges, or will they be held in place by glued t&g?

I got it for free, it's just a couple of samples. So how tight the fit should be? Should it require force to push the tongue into the groove?

The hallway is just 1m wide in its narrowest part. Won't the floating floor be susceptible to movement there? E.g. the edge plank pushed to the side under the heavy traffic. By the way, how tight is the t&g supposed to be in a quality floor? I got a couple of samples and the fit is quite...

Hi, I'm thinking about replacing my current carpet floor with engineered wood, but need some advice on the installation method. This is the suspended timber ground floor. The floor plan is as on this picture: I want to install new floor in the lounge (green and blue on the plan) and...

Thanks everyone for responses. The floor looks to be in good condition to me too, just wanted to hear some second opinions as I'm by no mean an expert in this. I'll do the 'screwdriver test' and clean up airbricks, as well as remove the organic debris when I will have more access. Is it...

dann09, I have 1 airbrick in front, about 24x17 cm and 3 in the back (24x9 cm) of this mid-terrace house. "Check that the exterior ground levels are below the DPC." - Do you mean DPC in external walls? I'm not sure where exactly DPC is there. How do I tell? I have solid external walls...

gregers, I've noticed that the photos were scaled down so it's hard to see anything on them indeed. These are in full size: http://i.imgur.com/CVxTZCt.jpg?1 - weird yellow growth http://i.imgur.com/uVhVJGk.jpg white growth. Close-up: http://i.imgur.com/Tt5a18j.jpg?1...

Pigeon85, thanks, I was actually browsing that site before I seen your comment! I haven't found anything that looks like my pictures on the 'NotMould' page. Does it mean it is mold indeed? :) It's white stains on the joists and yellow growth on bricks I'm a bit worried about. Does anybody...

Hi, I'm planning to replace the carpet on my ground floor with a wood floor and thought I'll have a look at what's happening under the floor. I lifted one of the floor boards and took some photos. Would appreciate if someone helps me understand if these photos look ok. This...