Search results

Thank you so much, light is now fixed, it worked!

ahh on same side, so this is the correct wiring? if you can confirm would be fab :)

ohh I see so like this?

yep thats what I did as shown in my diagram: I even did it the other way around so light pair of cables into load and fan pair into supply, nothing, not a sausage.

so I wired it up as suggested and nothing, wired fan live and neutral to end that says load, wired light live and neutral to supply, nothing, tried putting fan cables into supply and light cables into load, nothing. I have tried 2 switches now from local electrical wholesaler. Am I doing this...

Thanks Yeh well I thought that he would remember where the wires went, but he didnt. Should have just done it myself! ha Anyhoo so the block when wired should then be: top L red, top N black from one wire and bottom red L and black N from other wire. Moogie

Hi hopefully someone can help me. In my bathroom (which is seperate to my toilet) in my flat I had a pull light switch, this used to turn the bathroom light and the fanon at the same time when pulled. The toilet room next door to it has a flick switch which turns the light on in the toilet...

Recently I looked into renovating my kitchen and in particular was trying to find a cheap and effective way of making my kitchen cabinets like new again. They are a kind of off white cream, not sure if due to age whether they are that colour or if they were always that colour, but they looked...

There are other options: Spashbacks - http://www.ultimate-splashbac.co.uk/bathroom_splashbacs.htm brushed steel or shiny steel panels. Have you considered using floor tiles instead, larger coverage and more choice. there are specialist melamine and coated panels you can get...

silicone moves anyhoo therefore any slight expansion of a plastic bath should not make the silicone split. Unless you have had the bath fitted incorrectly and it likes to move of its on accord which it shouldn't. If you are really that worried then pull a long hair out of your head or...

Recently I looked into renovating my kitchen and in particular was trying to find a cheap and effective way of making my kitchen cabinets like new again. They are a kind of off white cream, not sure if due to age whether they are that colour or if they were always that colour, but they looked...

thanks :) email on its way to you.

ohh so you will be in the area then. :)

chap from ATAG (his name was Wayne Herbert) said that David or Simon would call me. But they didn't :(

Rebooted boiler like you said. Still pops up with Error 02. I called ATAG UK today and they are going to get a local chap to call me to arrange a service. Chap at ATAG said that the error usually pops up when it needs servicing. So am waiting for a call which will prolly be Monday...

I would mix a little cement and carefully fill the gaps on each side, once dry then silicone over. If you just silicone the gaps it won't do much as silicone moves. Moggie x

Hi, Hopefully someone can help. I have an ATAG bleuwe engel II combi boiler. An error keeps popping up on the boiler display as Err 02. In the booklet it says ignition error, no flame forming. Now if I press reset the boiler then comes back on. But not always, some days it lets me...

I turned the fill valve and topped the system up so that the display shows 1.3, the gauge moved a tiny amount, so gauge is a little out and will get a new one at some point. Reset the display, everything is working fine. Thanks so much for the advice. I now know to trust my instinct...

Haven't a clue what a brain unit is, I have a control panel in the corridor, as for outside sensor, what does it look like? Moogie x

ok checked the pressure today by pressing the step button and pressure says P 1.0. but when I look at the gauge on the pipe the black needle is pointing at around 1.7. Red needle at 2.0 Which is correct? If the display is the more accurate one whould I then attempt to fill the system...