Search results

I have an update - after the social housing guy came round Monday he mentioned the storm drain cover, but never looked in it. So just taken the cover off and yes it is storm drain - but also there is a branch heading to the bottom of the lawn. The drain is 70cm deep so not too deep, but deep...

Cheers guys, this is my problem - the only place i have to run the drains off to is at the top of the slope..... and with the fencing the way it is, i can´t increase the height of the lawn. The private property directly at the back of me has paved all his area, which probably isn´t helping my...

Thank you for the link. Doesn´t look good - High groundwater vulnerability, and for soilscape it´s Loamy and clayey floodplain soils with naturally high groundwater. I guess this confirms there would be no budget option to improve this. The warning signs were there as there are quite a few of...

Really stuck for a budget solution for our lawn. It´s a new build, we moved in as 2nd social housing tenants in July. Housing and developer not interested in doing anything, so we are on our own. Water pools worse bottom right - gravel board constantly black - but does pool all along the...

Thanks, no i don´t - that was initial research and just wanting the cheapest option i think just some 2x2 for the frame, feather edge instead of the slats, and then paint with some cupernol or similar.

Looking to build a bin store for the wheelie bins, crates, and bags. Looking at Wickes, i´m thinking pressure treated 45x70 for the frame https://www.wickes.co.uk/Wickes-Treated-Sawn-Timber---22-x-47-x-2400mm---Pack-of-10/p/261393 and 22x47 for slats for the back, sides...

Yep, no external temp sensor - whilst the new build was wired with 2 thermostats, that was as far as they went. Beginning to look like a complete overhaul is needed to get some cost saving smart features.

Hey, So this is my setup in the house i have just moved into - Vaillant EcoFIT Sustain 830 combi boiler with 2 wired thermostats - VRT 350´s, Plus the VR66/2 control centre. I wish to have smart features so i can control the heating via an app / alexa. Tado have said the VR66/2 is...

I have 5mm underlay which i thought would sort any deviations. I've just observed the machine on a wash, and the laminate plank under the front left foot is flexing a very little bit..... but not on a full spin, it only seems to go when perhaps the wash is uneven on a slow spin. There was no...

That was my thinking, but use 18mm osb..... but if i do that there's no going back, so would like to try other suggestions first. Like the one Mottie suggested in using L-brackets to see if i can firm up the laminate. But open to other suggestions as well.

Machine is brand new, only been installed a few days

The laminate is laid on a concrete floor, hence my thinking it's the laminate that's the problem.

I haven't a clue, no. I'm not convinced these anti-vibration mats work though, as thought they would cause more movement in the machine compared to being 'stuck' to the floor.... but hey i got to give it a go, thanks.

Thanks Mottie, The thing i hate most is having to get the machine out and back in again....... will def consider that idea though, maybe get a few ideas together and try them at the same time.

Well that sounds like a easy, cheap fix. And you've had no problems with essentially stopping it from becoming a floating floor? I admit i though of screwing the laminate down haha

Washing machine makes loud knocking noise on 1400 spins (transport bolts are out and machine is level) I have 12mm laminate on 5mm foam underlay in the kitchen to which the washing machine sits. The rear of the laminate where it reaches the back wall is somewhat 'bouncy' and i believe this is...

I saw the same thing on the Wayfair site, advertised on sale, but £20 more expensive. The reviews look good, some i've read have negative comments about installation, but none here - plus Amazon customer service is very decent, so any problems and they can be returned. When looking at...

Thank you, that is most helpful. I already have 1.5mm cable handy, but if 1.0mm would be better i can get that - which then i can get enough to run 2 cables from the landing light and be done with it that way. I only suggested the alternative as the cable i have isn't long enough to do that...

Hello, So, 2 x switched wall lights either side of the bed, nearest permanent live comes from the ceiling rose on the landing with plenty of room to connect the cable. I would like to take 1 x cable from the permanent live in the loft to above where the wall lights are to be situated and drop...

Forgot to add we have a PIV unit, so perhaps the best solution is just to close the vents up?