Search results

Thank you, that worked perfectly. The way I've done it is, I have the ring main coming into a J803 junction box, my mirror light and then a feed to a J804 junction box that powers the fan and ceiling light with the switched circuit. Thank you to everyone who contributed. I truly appreciate...

Ok, so I put it all back together as it was originally using wago connectors and whilst there isn't a light attached, I flicked the switch and the fan came on as expected. Now my next question is, how do I add 2 extra cables to power my new ceiling light (switched) and illuminated mirror...

The ceiling rose was completely untouched, those terminal blocks were completely vacant when I exposed it to take the photo. I will put it all back together tomorrow morning as it was, so we can start again. No wires have changed colours, but I have added new cables as the new light fitting...

Hi, apologies for the delay. Busy few days with work. I've opened up the fan and found it has red, yellow and blue conductors. Sunray, to your comment earlier. The ceiling rose photo was unchanged and before I started the work

Morning all, The light switch was standard 3 core, with neutral being switched live. When I opened up the fan Isolator I saw the attached, so I'm assuming the 4 core cable comes from here. I will also open the fan as I didn't have time this morning. Thank you again for your help.

Thank you, I appreciate your help. I will look at the switch in the morning to see what's going on and will revert back.

I joined the ring main in another junction box, as I alluded to earlier in one of my posts. I have a cable from that junction box feeding the one pictured above and labelled it as such

Not ignored, the fan was tricky to take apart to check the wiring but I get your point.

Yes sure, I will investigate. Shall I also look in the isolator switch?

I need to add an illuminated mirror to the circuit, which would have been difficult to replicate exactly in the new light fitting.

Going clockwise Top left Grey - spur from lighting ring main acting as supply Top right white - Assumed to be switched cable, neutral, live and earth connected to corresponding blocks. Yellow assumed to be switched live, connected to loop terminal on JB Bottom right grey - load going to new...

Tried yellow as switched live but it tripped the RCD. I also remembered there is an isolator on this circuit for the fan. Does that change things?

Thanks Pete. Just to clarify, the cable I need to figure out has Red, Blue, Yellow and Earth. So I assume Red is Live, Blue is Neutral, Yellow is switched Live. When I wire in my new light fitting, I will connect the Red from the light fitting to the Yellow, again assuming it's switched live...

Hi, I'm looking to replace the ceiling rose below with a new light and a little confused by the wiring. I have worked out conductors belong to the ring main and disconnected those from the ceiling rose and reconnected them and the other lights on this circuit all work fine. The 4 colours on...

Thank you. In my latest approach, I will have the transformer above the boards. The Ring power supply is a bit odd. It has a transformer that has a detachable 3 pin adapter which can then be attached to a longer figure 8 cable and 3 pin plug to extend the cable. In my latest approach I do away...

Thank you all, I realised that this at minimum would need an FCU and then the transformer under the boards ☠️. I found another way to shorten the run so the thinner usb cable protrudes out from the floorboard but the cable is unbroken all the way to the outdoor camera.

Hi, I am planning to hard wire my Ring Spotlight Outdoor Camera using the official Ring power supply. My question is whether I can hardwire it into my ring main circuit by cutting off the 3 pin plug, as the transformer is powered by the figure 8 connector terminating into the 3pin plug. I would...

Thank you for the input. I'm not necessarily after a separate switch but just a means to isolate the outside socket in the event of a fault or water ingress to stop the rest of the house tripping. Would the wessex product from toolstation acheive that?

Hi, I'm looking to install a waterproof outdoor socket by taking a spur from an internal socket but given it'll be outdoors id like to be able to isolate it using a 20A DP switch. However, it would be ideal if the DP switch was built into the outdoor socket so I dont have to have an knockout...

Thank you, that worked a treat