Search results

Thanks for all of the replies guys

Not going to be paying the £50 subscription this year, they are taking the p1ss... Any good alternatives out there? I have a Hikvision CCTV system and seem to remember they offered one, but does it allow remote playback?

I am wondering if anyone can advise which fence section(s) are likely to be mine? I am the homeowner. See attached. All sections could do with being replaced to be honest, most of the posts are rotten at the base and have had extra wooden support posts fitted. During storm henk the wind managed...

Correction - i am running 2x 20W halogen (not 35w) and 2x LED. https://www.easy-lightbulbs.com/products/halogen-spot-20w-12v-gu4-casell-lighting-35mm-10-amber-light-bulb?gclid=EAIaIQobChMIi5rs3dXw7QIVw7TtCh3lQALIEAQYASABEgIu0vD_BwE

I am running 2x halogen 35W (heat producing) and 2x LED bulbs (obviously producing no heat). Takes perhaps 20-30 mins longer for the full smoke effect that I used to have but works fine. Also lower wattage bulbs will help out with brittleness occurring on the lamp holders.

Agree with above 2 posts, I had similar issues, now i always go round with PTFE at least 20 turns, no leaks since.

Could go for one of these...

A few years ago i replaced my up and over garage door with a manual insulated roller door. At time time the best thing i could come up with to close the gap between the slats on the roller part of the door and the opening was to fit a brush strip. Is there a better way?

Not long, id say under 1 minute I set the amount, press the button to commence, grab a mug add a teabag and spoon, get the milk ready and the thing is starting to dispense. You can do two cups at the same time too, one for her indoors plus me! Looks like you cant really get the one i have...

With these 'One cup' ones i found that after 2ish years use they need replacing. The inside scales up and no amount of descalant seems to work, i tried to take my last one apart to clean it all but its a nightmare and ended up just buying another. I did find a different type, the Morphy...

Thanks for the info, I assume i need to buy a programmer that will connect to the Alarm PCB? I can't do it over Wintex?

Thanks fo the reply, I have often thoguht about updating the panel firmware, i am running 5.01.03 firmware, with smarcom version 03.03.00 I have an Elite64. Is it a simple process? Do you think it is worth it, i.e. are there critical updates / is my version old? I will try to contact Texecom to...

Hi, I have a number of GJA-000x sensors on my system. I have had two that have reported low battery events as tampers and as a result thrown my system into alarm. I have read on this forum that there were a number of these sensors that have this firmware bug. I have changed one of my sensors...

Use this: https://www.amazon.co.uk/gp/product/B08MBCKJPL/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 It comes with a coupler to connect your existing fibre cable to the extended one. Unplug the green capped fibre from your Openreach box (hard tug), try it in situ with the coupler and...

The easiest way is to log into your new ISP router and set the WiFi details (ssid and password) to be the same as what your old setup was. That way the Smart Comm will re-establish the WiFi link.

On the ios app i added a new site using the code from the alarm panel i generated, it did not add a new site like i thought it would, rather it said something like 'success' and then just showed my exisiting site in the app. It all then worked ok from then on, i did a sync panel on the app just...

Finally looked at this - got it all working again by generating a new app code on the panel and entering it on the iOS app.

Hi, I hae been using the Texecom app for around 1yr, recently upgraded to the new version 2, all was working ok. Last night i added a few extra sensors to the alarm, did not change anything else. When i now try and log in via the App, i get a "panel code not found" message with a "please...

Ok, thanks for your help. Ill live without it for now, hopefully Texecom will release a fix at some point.

Still cant get it to work, even with short names...