Search results

Thanks Boilerman, is that auto screw meant to be tightened right on or backed off slightly. It was loose when i checked so I left it that way. Only a 5 min job to nip it up if need be though.

Ok so this is weird, Left it switched off for about an hour, started fitting new shower instead, then gave it another try and it works perfectly now. Must have been either a short caused when the pressure released and soaked the front panel or a blockage/sticking valve sort of thing which...

Yep tried that, just took out filters on feed taps and they seem clear

Thanks for getting back, I have repressurised back up to just over 1.5 bar that didn't help other than letting the system begin the start up routine. When then routine starts the hw tap light comes on for a second then goes out when it stops. Dunno if that helps Cheers Steve

Hi can anyone give me clue on this, please. Got up this morning to no hot water, i have power on light but no others to help me. I have found that no heat is genetrated when the hw tap is turned on. When i switch th ch mode the programmer is calling for action and the boiler attempts to...

http://www.diy.com/diy/jsp/bq/nav/nav.jsp?action=detail&fh_secondid=9265050&fh_location=%2f%2fcatalog01%2fen_GB&fh_search=manifold&fh_eds=%c3%9f&fh_refview=search&ts=1196636849833&isSearch=true Sorry try this link

No More like this but with 8 connections http://www.diy.com/diy/jsp/bq/nav/skins/popups/scene7.jsp?skuId=9274750[/img]

Hi all, One of the connections on my Microbore manifold has given up on me and completley broken off. Does anyone know where I can go to getg a new one & roughly how much they cost. I am in North east England.

Has anyone got any ideas on this one? My 2003 Ford Maverick 3.0 XLT Auto (Petrol) has taken to stalling on an increasingly regular basis. It seems to occur when I have started to make a slow turn, off a closed throttle, previous approach speed does not seem to matter but I seems to occur more...

Hello all, our Hoover vacuum has started to play up. I have cleaned all filters & collector, checked for obstructions but it still is not working properly. The motor spins up to full speed then immediately cuts out however as it slows back down, just before it stops the motor kicks back in...

I have been using one of these for about a year now, got it off e-bay and connected it to a freeview decoder box in my glove box. As I spend loads of time sitting around in the car between apts, it give me decent sound quality and the ability to watch daytime films etc. I use a portable dvd...

Thanks all

Bugger 66% is a fail

Stab int dark PIR = Prof Inspection Report

Sorry Breezer but PIR? Cables are solid copper

Following my recent foray into replacing a ceiling rose, it occurs to me that I really dont know whether the electrics in our house is up to date or a fire waiting to happen.... My question is how long should household cables last before a rewire is needed? Some clues may assist your...

Hello again chaps, I would like to say a GREAT BIG THANK YOU for all the help today. I have finally managed to get both lights working properly and totally independantly of each other. I have worked out where I went wrong, by identifying the number one switch cable as the switch wire...

Sorry Switch 1 is for the Kitchen light Switch 2 is for the outside light

right chaps, this is what I have discovered: Took rose down and checked there were no more wires in the void Tested each wire to see what connects to what. I have three T+E cables entering the rose and one twin (no earth, looks to old and on testing does not appear to be connected to...

Thanks chaps, will start again, make some notes and if i still cant see the problem try to list a diagram. It would appear to be the fact that this outside light is in the circuit and I have still have this connected in, despite disconnecting at the switch but short of pulling the ceiling...