Search results

Thanks, I'll have a look at those.

Fair enough, to a point. How do you know that any certification mark printed on a box or product is fake or real? And perhaps 'oh dear....' might not have been the most useful response you could have given earlier on if there was a bigger point you wanted to make. Was that intended for others...

Yep, got a weatherproof junction box with stuffing glands, ready to connect it up.

Waiting for an answer from the seller, but other people have asked the question on Amazon and the seller has confirmed the warranty is valid. Yes, it's in China - not a great shock given that's where most electrical stuff comes from! The light is being fulfilled by Amazon so all warranty...

Thanks for your responses so far. The fitting is this one, IP65 apparently. Seems very well-made and strong having unpacked it today. https://www.amazon.co.uk/gp/product/B01M30R0EI/ref=od_aui_detailpages00?ie=UTF8&psc=1

Hi there, I would be really grateful for some advice please. I currently have a very old, very rusted, high wattage halogen floodlight on the rear of my house. It does not have a PIR and is switched from inside the house (as one of a 3-gang switch that also controls normal kitchen lighting). I...

Well, it's all gone swimmingly after all your great advice. Got a nice earth continuity using the resistance within the suggested figures and also did a basic audible circuit continuity test for sake of completeness and the buzzer in my multimeter sounded happily. Now got our new light fitted...

Folks, sorry, is the resistance reading meant to be zero or just very low as each of you said something slightly different! I've just tested my multimeter with an extension lead by setting it to the minimum resistance setting (200ohm) and then connecting the probes between the earth terminals...

Nice one. Just found an extension lead that has a non-moulded plug so just about to take the plug off and connect to the void earth and then use the earth terminal on the socket end to connect the meter through. Will use a terminal block as suggested to ensure connection is good.

Ok understand that now. Can see how you use an extension lead (it was the bit about taking the plug off that I couldn't see). So, given that there is no power involved anywhere, will any piece of cable do to make the loop? I suspect I've got a few metres of something knocking about somewhere -...

Confused now! I understood it that I connected a flying lead to the earth I found in the ceiling, then the other end to one probe of the meter, and the other probe to the MET. But I don't understand where I can use an extension lead - do I need to connect that to the earth in the ceiling...

Hi Phil/River, Thanks for this advice. To be honest I kind of prefer the method Phil suggests (no offence intended River). I think I can see the MET (looks like a large chunky piece of terminal block fixed to the board where the meters/fusebox are attached to, can see a couple of different...

Update - just found an earth cable tacked up on the side of the beam in the ceiling. Just couldn't see it from where I was looking up into the ceiling but stuck my phone camera up into the hole and took a few shots in different directions and there it was about a foot away!. It's been left with...

Thanks Phil, I have a sneaking suspicion that the earth at the back of the switch was installed at a later stage. I recall we bought the house from a builder who had taken it in part-ex and therefore tried to bring some of the wiring up to date before selling it on again. When we looked at the...

Thanks for the info. It's what I feared sadly. Suspect I'm going to have to go back to a simple plastic pendant/ceiling rose for now. The last spotlight fitting we had was plastic so just a L & N connection, but not much of that around now. I'll take a look at that site you suggested.

Hi folks, would really appreciate a bit of guidance. I have got a new light fitting from Ikea (I know, I know). On further inspection, it has L, N and E connections (it's metal). Having pulled down the old light fitting I only have a black neutral and a red live wire in the ceiling. Had a poke...

ok great, so fix a piece of 4x2 either side of the joist in line with it and screw through into the broken one, but outside the broken area? I think I may have found the duck!

Well I can't see a duck, but if you can see a duck in all that blown insulation, then that's all good!! So by fixing some 4x2, are you saying that it doesn't need any support 'vertically', just needs stopping from moving left to right? Or have I missed the point? Yes, the fall of the...