salus rt500rf

Anyone kmow anything about Salus iT500RX Receivers? My one is showing no power anymore and yet nothing has tripped on the board, which means it's not currently talking to my megaflow boiler. Any pointers? As probably guessed, I'm neither an electrician or plumber, lol! Cheers in advance

i have a SALUS RT500RF hand held controller and a VAILLANT combi-boiler. i recently had to change the batteries in the hand held unit and since then it doesn't actually control the boiler. both red and green lights are on on the receiver unit but even if the flame is showing on the controller...

Hello all, Probably my questions is weirdest you have seen. I have purchased a house last month and moved in. In this house we have a Baxi combi central heating. And I was given a Salus RT500RF Thermostat to control the heating. Now I want to replace this setup with Nest or hive and all my...

Hi all, Looking to swap out my existing Salus RT500RF with Nest 3rd Generation. Combi boiler so only heating to worry about. Nest thermostat will be talking to HeatLink wirelessly only. Looking at the current wiring [see attached] I think it’s just a straight swap, but just wanted some...

I have a RT500RF thermostat and RT500RF(RX) receiver. All is working correctly but i think I'm getting interference from a neighbour. My receiver differs from the one in all the documentation (maybe its old?) and looks like this...

My Salus rt500rf programable thermostat is acting bonkers. Had it working fine for 6 months, now its going crazy. It has been used on its factory settings, 22 degrees, manual and no programed on/off times. In the early hours of the morning, around 3am/4am it ignores the set temp on the unit and...

The boiler's circuit board is unlabelled, but based on the current configuration hope someone can help check my deductions/proposal... At the moment: Programmer/Timer (Sunvic Select 107XL) N/L connected to its own fused spur power supply. 1/COM is connected with a Brown/Live cable to the...

Hi Guys, New to this, so please be gentle :) I have just been given a Hive Active Heating system, single channel for a Combi Boiler and need some help with the installation. My current setup is a Potterton Promax Combi Boiler, which is connected to the mains via a fused spare. Installed in...

Hello I was wondering if someone could please help me out with installing the new Hive receiver/thermostat. I thought it would be a simple swap but I'm a little bit stuck with the wiring of my current receiver. I have a Valiant Ecotec Plus 831 boiler with 230V supply. It's receiver - the Salus...

Hello I could do with some advice on changing my analogue stat for a Salus RT500rf. I have a Worcester boiler and my hope was to simply swap over and run a sep mains to the same source as the boiler and then use the existing wiring for the stat to Salus. My boiler has an analogue programmer...

Hello, I am.hoping some one could help me in regards to my problem I have recently changed my standard honeywell thermostat with a salus rt500rf unit so that I can use it upstairs wirelessly. Now that I am not technical and also first time exp with this please excuse my stupidity. I have...

Hi all, i have bought a Salus rt500rf to work remotely from the boiler, as a room thermostat. The wiring diagram with the product shows 4 wires to be connected 1 live 1neutral and 2 wires as a switch to be wired into the place where an existing loop wire is. Now on a link for wiring it says to...

Hello there. I am not very technical, so please forgive any stupid questions or comments. I had my thermostat replaced with one of these last week, and I cannot seem to get it to work correctly. I have read the instructions and set it up, but the floor which this unit controls never seems to get...

Hi guys, Its my first time here and its great to see the amount of information you can find just by browsing DIYNOT. I've been reading a lot about the problem that i am facing and i've seen there were very close to similar posts on here but nothing was like mine, at least i could not find it...

Hi all, saw previous thread similar but it didn't answer my question, which is that I have fitted the unit, set program and get both red and green lights when thermostat is lower than required temperature. So all looks good, however the boiler does not kick into life. When I bypass the timer...