Recent content by Sayer

  1. S

    New house vailant boiler

    Sorry for the delay . The rads have an output of approx 6.1 kw . I'm still running the flush through as my plumber has had to do some work on my old house . ( Worcester leaking at boiler ) so the pump hasn't been changed yet . i have been waiting for the pipes etc to be flushed before putting in...
  2. S

    New house vailant boiler

    Ok got a 15/60 grundfos , do I run it on setting number two or three. Just out of interest if the flow is too slow will it damage the boiler.
  3. S

    New house vailant boiler

    Evening all , just an update , heating seems to be working ok at the moment , I think mainly down to reducing d0 which has virtually elinimated s53 waiting time . I will change the pump for a ups2 15 50/60 , should I set the new one to number 2 or three as having the existing pump on three seems...
  4. S

    New house vailant boiler

    No sign of pumping over
  5. S

    New house vailant boiler

    Right . At the moment the boiler seemed to Be very slow to heat the water in the heating circuit so like a dick with very little understanding of whatiwasdoing I upped d0 to 12 , I then got an s53 status which after a wait cleared started to heat again then back into s53 . Can anyone Explain to...
  6. S

    New house vailant boiler

    Ok will check , what would that suggest ?
  7. S

    New house vailant boiler

    Meant to say what does pumping over in the Roy mean ?
  8. S

    New house vailant boiler

    The magnaclean came with mc3 cleaner and 1 inhibitor . I've got to put the cleaner in before the magnaclean is fitted next week as we really only have one day of my plumbers time left which is when he will drain and flush through the system and fit the magnaclean thing . It came from my local...
  9. S

    New house vailant boiler

    Yep there is a gate valve on the return of the hot water cylinder . I left the heating on and turned the stat up on the cylinder to force it to call . Pump is set to 3 , the tank has a lime green coloured insulation , . Sorry but I'm not quite sure what modulation range is . I must admit I was...
  10. S

    New house vailant boiler

    Hi all , right I've done what I was asked to do and here are the results . Set d0 to 9 Set d1 to 10 Temps were Initial temp 12 degrees 1 34 10 2 40. 14 3 43. 17 4. 46 20 5. 48. 23 10. 57 32 15. 65 40 20. 69 46 Dial on heating is set to 70 degrees Heating only demand no hot water...
  11. S

    New house vailant boiler

    Will do and will report back , pipes not to bad a trace of black water at the end when the system was drained down . Cheers again for your time I do appreciate it
  12. S

    New house vailant boiler

    Hot water tank heats up though , wouldnt heat exchanger stop this from happening ?
  13. S

    New house vailant boiler

    Ok thanks will try , also just wondered if hot water could be nicking rad heat . I think the valve on the return hot water is fully open bar 1 turn . I'm not at the bungalow tonite but I'll record the figures and post them tommorow evening . Thanks again . Pump too small , its set to number 3...
  14. S

    New house vailant boiler

    hi all , I was hoping for some advice please . I recently moved into a bungalow with a 2008 ecotec plus 418 boiler . The system was using a mixture of the old underfloor microbore pipe and two rads supplied with 15mm . We never tested the boiler before we started work as we were told that one...
Back
Top