Afternoon all!
I have a small office at the front of my house with a floating bay window, which I'd like to knock through to create a 'proper' bay so that I can create a desk space in the resulting recess. Having read up on a few other forum posts and spoken to some builders I have identified 2...
Taking it back would require un-installation, which I was looking to avoid. I've actually managed to figure it out myself, there's a double ended threaded retaining ring that holds the cartridge in place. It's not obvious how to remove it - I ended up using a pair of long-nosed pliers up against...
I've recently had a 3-way kitchen tap fitted (hot, cold and filtered). It's been in a week and I've noticed it's weeping slightly from around the edge of the hot/cold tap head. I've taken the tap head apart, hoping to find a loose nut or washer that needed replacing, but I can't see how to...
I'm looking at getting my existing conventional boiler replaced with a combi and having had Ideal branded models in my last 2 houses I was looking at doing the same again (Looking at the Vogue Max 40 this time). In my experience the Ideals have been well priced, trouble free and with an...
So I replaced the fuse on the RCD fused spur today (with power off at the CU), and as soon as I switched on the power at the CU both the MCB and RCD on the CU tripped. I went over to the fused spur and could smell something hot and electrical so I've just popped the fuse out altogether. Guessing...
Apologies for the slow response, I have tested the external sockets and can confirm there's no power getting to them so will be replacing the fuse in the RCD tomorrow to see if that does the job.
I will test the sockets this evening to check for power and report back - that should help clarify the state of affairs. Thanks for all the responses so far!
Ok, just to clarify my poor description at the start:
The indicator is showing red which is indeed supposed to be ON. If I press the 'test' button, this (from memory) should 'trip' the RCD and set the indicator to black (off). You then press Reset to turn it back on (red indicator). At the...
Correct.
Not yet, I wanted to ask if it was the right thing to try before trying it!
Fair enough, and thanks for the response. Any other ideas on what could effect an outdoor socket in a way that would trip the MCB and blow the fuse? The weather covers are in a pretty poor state so I was...
As per AndyPRK's correction, it was a 32A MCB on my CU that tripped out (my mistake in the OP). The one for all the sockets in the house. When I first reset it, it tripped out again straight away, so I went round the house and switched off everything plugged into a socket and reset it again...
I dont have a 30mA RCD in the CU. The fused spur is running off the 32A RCD for the sockets (which is what tripped originally). Pretty sure the sockets are dry, they just popped open one day when it was raining so it wasnt gathering water over a long period. Plus it's been months since it...
Due to some unusual wiring by the previous owner, there is a pair of outdoor sockets wired into a 13A RCD fused spur in my kitchen. Recently the weather cover failed on one of the sockets resulting in water ingress which tripped out the main RCD on my consumer unit. After fixing it and resetting...
I have air stuck in my hot water system which is characterised by a loud humming/vibrating noise coming from my hot water pump every 10-15 mins for about 3-4 mins at a time (presumeably as the pocket of air cycles around the system and hits the pump). I have tried bleeding all the radiators in...
Hi all,
I am just in the process of having a new woodburner installed after having an old gas fire taken out. I am using a HETAS registered fitter for the job but have had builders in doing other work around the house as well. I have an external chimney stack so the fitter initially just opened...
That's not actually the case, it just appears that way from the photos. The black and green lines from the supply are not connected to anything, they've just been twisted together and left unterminated. The only lines I'm looking to snip are the 2 blue and white ones which join the black cable I...