Search results

Hopefully this is ok?

Hi no just want to have 1 x led dimmer 2 gang 2 way and leave the other normal 2 way switch Will send a photo of wiring shortly …

Hi everyone I have a 2 gang 2 way light switch controlling 2 lights from either side of the room. This has the usual Commin L1 and L2 ports. I have a 2 gang 2 way led dimmer which has ports Sw L and x - I say x because it’s like an arrow with a wave through it. Wondering how I can swap the...

Hi im getting the garden patio relaid and want to put in an LED border around the edges of new slabs- about 65meters. I have a power source internally where i can power the LEDs, but wanted to see if there are any recommendations/brands to avoid, whether i need waterproof channels or if some...

Ah yes sorry get you now. I wrongly assumed the double check valve had an iso in there. Internally what would I fit first from the main, the double check valve and the iso before it goes external?

thanks guys. got a double check valve ready to connect to one of the existing pipes. the water is mains fed not tank fed. the second iso valve you specify above - whats that one for if i already have a double check valve?

Hi all Wanting to get a cold supply of water to rear of garden that’s about 20m away. I have a down stairs shower room where I’m hoping I can tap into the cold water supply and feed outside with a iso valve maybe on the inside in case I need to cut off the water but was looking at the thermal...

Yes thanks that’s worked fine.

Thought so- just wanted to make sure. Will let u know if it works

Hi I have 2 sets of lights that are controlled by 2 different switches (2 gang 2 way) from each side of the room. One set of switches, they are all in the “off” position. The other side, 1 switch is off, the other switch is in the “on” position but the light is still off. So in effect one side...

Thanks got it working now. 34 en50131 is disabled 53 pd6662 is off Thanks everyone for your help again.

I had lost a lot of settings about a month ago so had to reconfigure a lot of it. So arming displays when in progress but when armed we used to see the message like “full arm” or “evening arm” but handy when you know it need to be disarmed? Will see if I can find the area settings, thanks.

Hi Got an issue where when I arm my system, full arm or part/evening arm, it works but doesn’t display this on the lcd. It just shows the date and time. Not sure how I’ve lost this but only noticed recently, does anyone know how I can get this back on pls? Thanks

Hi reading a lot of posts about this and how the outlet pipe needs to be around 16” or so inches from the ground outside. My question is that I have to cut the outlet hole but want to avoid that unsightly pipe on the outside and want to have most of vertical pipe within the sink unit and when...

Thanks- didn’t wana use too much adhesive to stick Mat to floor I will see what’s available my trowel is 12mm for sticking on tiles.

hi, what size trowel notch did you use for sticking the matt down to the floor?

Thanks mr chibs. I will get the same primer from local store. I will try the proflex to stick the mat to the floor and see how it goes.

Hi I am looking to start tiling on a new project. Have installed underfloor heating pipe work and had liquid screed poured on about 3 months ago. Heating working fine. I have had the floor polished as well. I have brought proflex so s1 bags to lay the tiles and have brought durables rolls. So...

ok made some progress here. looks like the panel lost the fact that comip was setup on com1, added that along with the ip addresses for comip as per the comip manual. made the test call successfully. so connection via app and wintex works. issue now is i cant set the alarm cos of No ATS...

Hi The internal ip address is correct and as expected within the control panel . I can ping successfully the ip from computer and when I enter in the ip address into web browser I get the comip layout diagram. Don’t think I’m using away from home but got port forwarding already setup as part...