Search results

Thanks for that reply, bizarrely I went to tap the gauge but it was already showing 1bar This was several hours after I last checked it. I will keep an eye on it

was using the shower earlier and the temperature kept changing. Checked the pressure gauge on boiler and it read zero, opened the top up valve and could hear water flowing in, after a minute or so the flow seemed to stop but the pressure is still zero. I'm getting hot water at an even...

What I did in the end was to fix 6 metal repair strips across the crack, recessed into the tread and filled the crack with glue. Seems to be perfectly solid now :lol: Thanks for your advice :D Now to get on with the painting and wallpapering prior to new carpet arriving, phew.

It's not very wide, I can't get a flat head screwdriver tip in it, but I can get a Stanley knife blade in some of it. It has cracked all the way through so there is some flex when i stand on it. I have some thin plywood that I was considering cutting a piece the same size as the tread and...

Just ripped up old carpet and underlay ready for new carpet in a few weeks and found one tread has split all the way across. The staircase is closed in with a wall either side and the tread looks tied into the skirting running up the side of the stairs. I have no access underneath...

Cat is all fluff :shock:

It's 46m2 total inc area already paved in front of door. The highest point is at the back fence by the swing. It slopes down from there to the door about 6" Requirements are nowhere for dog to get muddy and an area big enough for table and chairs to dine out in summer. Had a think last...

Rear garden is currently turfed but we had a nightmare this winter with all the rain, the garden was a bit of a swamp (clay soil) and the dog brought most of it in the house! So we are looking for alternatives.....gravel or mulch aren't really an option as the dog would probably eat it! If we...

thanks for that how do they stay on once they are located?

thanks for replies so far. yes there are 2 hinges and they on the correct sides and i can get them to fit but then once i close the door and reopen it they have come off at the bottom, where there only seems to be the notch holding them on?

Trying to re-fit my servis oven door but its not happening! I have worked out how to lock the mechanism and release once in place BUT the bottom part of the hinge doesnt stay in place once the door is shut and reopened - see pic, ref A points to the notch which sits on the bottom of the hole in...

thanks for your reply, however, i did say that it doesnt get as hot as it used to (we have always used the half heat and it used to dry the clothes easily)

Having a heat problem with this dryer half heat is not as hot as it used to be, its more luke warm (High heat works fine) Is this going to be heating element or thermostat? Thanks in advance

thanks guys, great help

I am fitting a new kitchen cabinet where the boiler used to be and im unsure how to fix it. The brackets have holes for 6 screws. I know i already have some grey plugs, brown plugs and an assortment of 2-3" screws. think i also have some hammer-in fixing which might be 3"? cabinet carcass is...

Since the triton guy changed the cartridge the problem has gone away :D

Thanks but i need more like 22mm as its 2 tiles thick plus adhesive :(

I am about to put up a 400 mm wide kitchen cabinet (as ive had to move the CH boiler upstairs) BUT i want it level with my existing cabinets but the tiles are too high (2 thicknesses of tile as well as the previous owners tiled over the original tiles How hard will it be to remove 2-3 cm from...

Ok, had an engineer from Triton out today and he has replaced the whole cartridge, lets see if that fixes it, ill keep you posted

i also have this problem with the same shower, had service call once (its got a 5 yr warranty) and he said a part inside had been installed wrong and corrected it, but still have same prob, service guy is coming again this week but if any of you guys can help i would be grateful for any other...