Search results

So deck is over & measured at 20 inches side to side.My old deck to blade is about an inch gap either side so i wil think i will order up an 18 inch blade for this

I don’t. The blade boss looks the same so I’m thinking the blades are the same just length is different.

no no no I need to buy a blade as the owner of the one i took from tip removed it. So i need to replace it. So as i have nothing to go buy the inside distance side to side is 20 inches So i was asking do i just buy an 18 inch blade.

Ok with regards the blade do i meaure inside distance & take of say 2 inches. That then leaves me with 1 inch clearance from tip of blade to inside metal of deck. If thats the case ive seen an 18 inch blade. Both decks are mountfield so i suppose i was asking Do Mountfield use the same hole...

I attach engine from new mower. Deck size. Old mower showing crack & width of deck Inside diameter old new deck is just oevr 20 inches

Hi, Towards the end of the cutting season my deck on the mower decided to split a good 4 to 5 inches & in the past ive welded a plate on i thought it was time to stop due to now the weight of it etc. I picked up another mower & have been using that with no issues but what was i to do with this...

sorry its too late

Dont worry about a reply as ive just thrown it 50ft up my drive. Just a bad day Thanks

My FS120 had a broken wire & fell on the floor. It was part of the coil so i purchased a new coil & now trying to fit it. Now i had 2 wires coming out of the case which were connected to a kill switch to stop the engine. There 2 wires were both on the coil,lower Red wires in photo. With cover...

When the air filter is removed the air that enters the carb is more. So the mixture in theory is weaker. Should I set up the L screw nearest the engine to accommodate the engine to run with air filter left in place. Never had this issue before.

Yes to bulb. I do prime say 6 times. Will try more or less tomorrow. Thanks.

Ok tomorrow I will try that. So what do you decide why it’s hard to start & when it starts I surely should be able to start it without pull pull pull

Started a new thread as thought it would be easier. Strimmer a pain to start. After getting it started I can use it fine no problem. I switch it off & reload the line. Now I go to start it again bearing in mind it’s warm & I’ve been using it for say 15 minutes. Pull after pull after pull...

So in the photo you are saying bend it TO THE RIGHT correct ?

No this one

Well i did assume i bent it but it was done it situ. Isnt there a sure way to bring rpm up more so at least the speed of the thing moves along quicker. Does adjusting the self propel new cable help with this ? This grass isnt long & mower crawls along,any grass that is a bit higher i think it...

This is why i want the rpm to increase. I have the throttle set at HARE & have bent that rod as mentioned on the carb,did it in situ so assumed it moved ? It will take ages to cut lawns like this so what do you think ? SHORT VIDEO CLIP HERE Actually watching the video it looks faster that...

Cheers. I am now nearly finished but just these 2 things to do. Remove that strong spring on the stop / start arm as when mowing you see the lever creep & engins dies. Need to stil get revs up & couldnt easily bend that rod. Unable to alter cable as it locates in a slot in that clamp. Jobs...

Ok now sorted, Ive done much better on The Krypton Factor. Not only do you have to have the drive pegs in the correct orientation BUT also the metal gears that they lock into. These metal gears look the same either way round & one side has a plastic bush / seal fitted. After many tries i...

Ok so this is what ive done. Removed 1 wheel at a time. So left side i see a circlip, metal cog wheel, pulling that off i then see the peg item that has slanted sides passing through the shaft. I turned the peg around & put it back together & operated the handle but still no drive. I removed the...