Search results

I have a Clark pls190, had a job the other day where the water flow wasn't enough and the machine was getting starved and loosing performance, now I'm wondering if I can convert or modify the pump so it can draw from a barrel? Clark tell me this machine only runs off a tap but the tap I was...

Hi john, the machine is ok, I've done two jobs so far a block pve drive and a decking job, the decking was easy, but think I could do with more pressure for drive work which I hope to achieve by fitting the turbo nozzle as when it's on the pencil position it's good but to slow and as soon as you...

Anyone know if a turbo nozzle (the spinning type) will fit on the Clark pls 190, if so what make would be suitable and best performing, thanks.

Hi john, I bought the pls190 in the end and did a 4 hour job yesterday, seems ok at moment😜 but having worked a lot on motorcycle engines in the past find there recommended oil (sae30 mineral) a bit strange when there are some good quality synthetic oils around, what do you think? Also...

Yes I know and it also says it need 5 gals pm to feed it which dosen't make sense?

Yes my thoughts as well about the possible printing error, I think I may go for it because correct me if I'm wrong if you turn the machine pressure down then I'm assuming the machine will not need as much water :?:

Thanks for your reply john, I have a very high water pressure where I live probably near 15 ltrs pm, but where I will be using the machine will be a lot lower maybe 50%, bearing in mind this machine has a flow rate of 12 ltrs pm I am stunned that the makers state in there manual that it needs 5...

Hi has anyone used one of the above from a normal garden tap supply? The reason I'm asking is clark online manual states that it needs 5 gallons pm inlet supply and I don't know of any garden taps in my area that will produce that amount, I've spoken to clark who have said it will run ok of a...

If I were to hire a scaffold firm to erect scaffolding for me to work on roof who would be liable for any damage caused by the scaffold, ie erection, dismantling, or collapse, me or the scaffold company?

So I'm assuming the washer won't run if there's not the same supply as what it produces ??

Ok think I've decided on the machine, only thoughts now are if the manufacturers state say 12 ltrs per minute flow but the supply tap won't give that amount what happens?!

Hi, can anyone recommend a decent mat finish sealer for block paving. Is there an all in one sealer/weed killer?

Thanks for all the info I'm now swaying towards the Clark pls190 6.5 hp brass pump head 2700psi about £400 :D

So you wouldn't recommend the Wolf at 3000psi 6hp £250? What sort of price should I be looking to start at then?

Hi I'm looking for a decent pressure washer proberbly petrol driven for cleaning drives and patios etc, not for every day use may be 2/3 times a week, anyone know what I would at least need in psi? Seen a few 3000psi on amazon etc for around £300 new, also dose anyone know the life expectancy of...

Thats exactly why I didn't call a reg engineer, I don't want a new 3k plus boiler, by the way it wasn't the relay! Next try is the spark generator?

Hi I have a problem with the above boiler, it comes on, fan runs, but wont fire up, I had this problem 4 months ago and changed the relay, could this have gone us already? There is no sound of the spark ticking when switching on.

Hi I have a DWD4310w dishwasher and the on off switch is faulty, is this easy to change ? Has the door got to come off and be completely striped? I dont want to strip the door out if theres an easy way to get to the switch.

Had the above microwave for a out 30years!! Its been fualtless up until now, bit reluctant to buy a new one as this is stainless inside and the quality nowdays is s##t, the problem is the fuse (5amp I think) inside has blown, I replaced it and it blew again!! Anyone know what the prob could be????

Ps. Where is thr BSI located ?