Search results

It stays red (1st led) regardless of the door being open/close however the third led at the end goes green or off when away/near the magnet . It doesn't reset with both tamper's pushed in

An update: 1) I found the "Utility" DT sensor with low battery and that code has cleared following a new battery being installed 2) I tested the tamper on the magnetic sensor and it doesn't seem to be the tamper as the light goes off when both tampers are pushed in. So I am thinking it isn't...

Thank you, I will check that. As I only saw the front tamper and when I clicked that, the lights reacted. It's odd, it's still holding the PIR tamper fault as well. I was wondering if the tampers don't clear until that "DT low battery" warning is resolved, I just need the time to go up on...

If you look at the top left of the door, you will see the door contact sensor, it's black so not easy to see. edit: I took a photo this morning.

I think because the installer decided that would cover the glass if anyone came through it or presumably if they got up there and started looking through that window. It does seem they were "creative" as they also strapped a PIR into the car footwell of the previous owners car, so it was linked...

Hi sparkymarka So these are the three devices in the utility. The battery in the shock that I changed a few months ago. The PIR (2x varta CR123) and the door contact sensor one varta CR123 (black one hiding at the top left) are pictured below. Can send close ups if if that helps.

Thanks T1GERIII both the cover on the door contact and the PIR are back on and secured back by screw (along with their respective new batteries). I might take another look at these tomorrow, but it does seem odd that they both are flagging as tamper rather than low battery, then there is the...

Hi All, So I have a Pyronix enforcer (with the WiFi module) fitted around 2022. Albeit I don't know who by, as we bought the house in 2024. I changed all the shock sensor batteries a few months ago and one PIR that was flagging as low, but not any of the other contact sensors or PIRs...

Thanks, I did exactly that and all resolved now.

Hopefully the attached helps? 1) shouldn't the valve I have circled be closed? 2) I have attached a close up of the valve on the right, that seems to be closed on both the toggle and then a seperate screwdriver slot? - Seems odd but perhaps not

You are right, all my previous boilers were combi's. Whilst this one is indeed a system boiler connected in the same boiler cupboard to a megaflow type system, with diverter valves to independently control upstairs and downstairs. The model is ecofit pure 630. The only braided pipe I can see...

Thanks, the picture has all of the pipes running to the boiler. Ultimately there is one turnscrew valve over to the left and one to the right of the yellow gas valve. Presumably it is those then ?

So I just noticed my boiler is sitting at 0.6 to 0.7 bar and it should be closer to 1-1.2 bar. I looked at a few online videos but none seem to match my config. I thought the yellow lever would do something, but seemingly not. How do I get a bit more pressure into the boiler ? Thanks in...

Thanks I will thinking something similar, I will push as much of the lead back up and then seal

Hi All, I have just moved into a new property and noticed whilst up on a ladder this hole to the side of the lead roof (above a bay window). Annoyingly it is somewhat new, but a tile must have fallen on it. Any suggestions on how to patch it? There are no water leaks inside the property. I...

Hi All, We have just bought a house and it had a recent extension in 2022 (so will be modern construction methods). My problem is this, I have a 77" LG G2 ready to go on the wall but I have sockets already in place, on this model the bracket ount is at the top and the bracket is very flush...

The MCB is a 32a for that thing (sorry my dad has been relaying messages to me, and every time it changes). So now I have looked there is a 63a 30ma RCD but the specific one for this circuit is a 32a MCB

Thanks, I just realised I made a mistake in my description (and have now corrected it), it is a 63a RCD, presumably this will ok?

Thanks ree

Hi All, We have just moved into a house that recently had an extension built. Basically it seems that in the utility part of the extension, the wiring is connected to a 63a 30ma RCD in a new consumer unit. On this single ring, there are 3 double sockets. The way I plan to use the sockets are...