Search results

Conduit is threaded at fuse board positions. Not sure about ceiling boxes.I’ll need to drop a light fitting to check. Does it matter about material?

Hello I need to have an existing fuseboard upgraded for insurance reasons. The property is a 1 bed flat with concrete floors and Ceilings. All cabling is done in buried steel conduit. The ring, cooker and immersion heater circuits are using twin and earth cabling. The lighting circuit currently...

Hi DP Thanks for the reply It’s probably cos I’m used to using my own home combi Honeywell system differently. I only use the set up there in MANUAL. I only turn heating on when I need it, otherwise the property would be heated when nobody is in, or I’m busy enough not to need it. So I turn it...

Good Morning Stem Thanks for detailed reply. Tried searching for a suitable stat to pair with RX1. Danfoss site only lists current products etc I’ll try to get in touch with them on link you provided Cheers

Good Evening I’ve just bought a property that has a Baxi Heat only boiler It has a time switch setup for controlling times of HW & CH HE is working fine My question relates to CH Adjacent to timeswich is a Danfoss RX-1 Receiver In the hall is Danfoss TP5001 RF I believe the TP5001 is a...

Hi Keith Thanks for pointing me at this thread from KugaOwners. It’s taken all morning to read right through. I’m knackered, but it’s a great read. Your patience and perseverance is to be applauded. We’ll done Kelwyn

Your inverted advice is that I’d be no more at risk if I removed it and just used an isolater?

What is ?

No it wasn’t cos it was £2!! It was because it was the same spec as the original AND I wasn’t convinced it was the root cause of the fault, but it had to be eliminated. As it happens the fault hasn’t been cured. So now I have proven it isn’t the RCD and I need to look elsewhere. AND I didn’t...

Thanks John I totally accept that safety is paramount. Just out of interest I had quick look on Screwfix and was surprised to note that they sell populated consumer units. Some with AC and some others with Type A rcds I assume the type A is now the preferred choice for most domestic...

Hi No I don’t consider cigarettes safe. However until legislation changes and cigarettes are banned, they will be sold. Question. Do you consider AC RCDs unsafe? I will accept that you wouldn’t install one in a new install. However does that mean every home, building etc that has them...

Hi So it’s obsolete in manufacture? But not unsafe to use or replace like for like? It’s in a garage that has 8 sockets 6 lights on 2 switches And 2 external security pir lights Unless it becomes mandatory , no further action required

Because it is readily available It complies with same safety requirements. It is physically compatible Why would anyone fit Michelin tyres to a car , that left the factory on Nexen? And there is no name on Consumer Unit housing. It contains 1 hagar RCD and 3 MCBs (2 Wylex and other). And...

Ok New device fitted All circuits re-connected Everything works so far Time will tell.

Typo sorry Specsavers next on list 40A. 30ma

Hello Flameport It’s got the same markings as the my Hagar that is currently in situ. For £2 it’s got to be worth a try. Just paid for it. On my way home to fit. Incidentally why is it obsolete? Must still be safe or BandQ wouldn’t/ couldn’t sell it ? Actually it has same markings as the one...

See previous reply to ericmark Thanks Harry

Hi ericmark That’s I am now. Would an RCD trip if there was a problem either incoming cable? So I’ve elected to buy a new RCD. Had a quick Google and found on the B&Q website a British General 43a device. It’s in their Clearance section priced at £2!!! So I’m off to get one at nearest...

Hi The RCD is in the consumer unit in garage. I isolated the 3 circuits to check if it was 1 of the circuits causing the problem But with no wires connected, apart from incoming feed and extra earth, it still trips.

Hi Problem with garage supply I have a small consumer unit in Garage. 1x 6a and 2 x 16a MCBs And. 63a RCD For no obvious reason the RCD trips I’ve isolated all circuits from CU. I.e. removed all neutrals and internal earths and turned MCBs off Still trips for no apparent reason Garage is fed...