Search results

No Idea, your saying the switch doesn't do anything? You would have to trace it to what is on the other side of the wall/ up the wall ......external light maybe just guessing randomly The non switched fused spur is below the panel.

Monitor mode can be enabled and that overrides all the comport settings. You can then go back and reset things up without monitor mode. As the smart coms is connected to the WiFi, you should be able to see the Texecom device on the hub, used to show as texe_hub, but doesn’t anymore. So you can...

Have you tried to generate app code via monitor mode? This overrides all the settings. If that generates the app code go and look at the programming back on. I have reset many smart coms for new customers and it literally is a very quick process. You can try turning off routers firewall and...

Apologies but this may sound rude, you think you have it setup that way. It’s clear the smart com is connected from what you have said. So if the comports are correct and the program did go correct you can go and turn it all back off. Unplug smart com wait 20 seconds, plug it back in and...

In program digi how’s it programmed?

so in comport set up do you have com1 set up as smart com and com2 as com ip, its a bit of a stretch on the 24 if I recall correctly the positions of com 1 and com2.

Where is the 4 wire lead going to on the elite 24 and where is the two wire lead going to?

What are the lights doing on the smart com?

It’s difficult without registered trademarks to prosecute but not impossible. To be fair a few that have tried to copy have gone under with similar names. I get reports from others in the trade when they see someone trying to go to cash in. It helps me as much as it helps them to be fair, in...

Not had vans for a while, as for advertising we don’t. Had a few trying to copy!

i would look at your immediate needs and possible future needs, to save money long term. That may mean looking at a 48 instead if a 24 for example.

The LED status is covered in the manual for the odyssey series. There are few things the comfort LEDs indicate. I very much doubt you will need to be replacing the bell battery if its only 4 years old. Yeup very windy here also.

Costs are interesting. As panel, keypad, communicator, to get it up and running and app costs, for year on year running has to be considered. But you can’t guarantee that an app free today will be free tomorrow. So bare that in mind. For example Texecom keypad panel and communicator can cost...

We offer cheaper prices for the app for pyronix. As which panel, better to look at your current and future needs, to try and edge your bets. Both of the above suggestions are readily available to the diyer. As for programming that’s where people make the the most critical mistakes.

The Veritas will depend on its age and if the strobe wire is connected. So if the panel uses prog to get into the menus can’t remember if there is specific menu to do this, something is telling me maybe. However strobe test you can activate strobe on and off three times, you can then check...

Yeup frigate will probably give you the best from the video feeds .

these are or were sold on eBay for very little for the whole system, 30-50 for the panel and a load of sensors. Took one out years ago after it had failed. No idea if you can still get units on eBay to replace like for like for little money, but isn’t something any of the installers on here...

Firstly, I would advise updating your smart com to the latest version, you should fair a little better with it, as you have version 5 firmware you should also be able to update panel firmware via the cloud also, if you have your own cloud account. There were a few design issues with the latest...

Discord has a 13 age limit. the video, appears to be about adding discord to ps5 so you can chat on discord. but doesnt appear to allow ps5 chat on ps5. the mobile app works okay, so still have to look at getting the emulator or something on the pc. got his internet speed up, rather than...

lol but not a surprise might get a chance to look at this in next few days