Search results

Why would the socket need to have a double pole switch? Surely any heating engineer working on the boiler could isolate it safely by simply unplugging it.

That makes going from the feed into the garage straight to the shed a fairly reasonable idea I‘d say.

Depending on what you want to power in the shed, the easiest way might be an RCBO in the garage CU (20 A), sockets in the shed powered directly, light via a 5 A FCU. Just something to suggest to your electrician.

If the neutral happens to break somewhere in the three-phase part of the distribution you‘re in a world of pain because single-phase supplies or circuits end up effectively in series between two phases, with fairly unpredictable voltages depending on resistance.

Early 90s Legrand MCBs definitely have a trip position.

You need to figure out which wire is the incoming permanent live. I‘d probably do that by putting each grey single into its own choc block, turning the electric on and measuring between each wire and earth. The one that gives you 230 V-ish is the one you need. Connect it to one of the COM...

We can’t tell without pictures but the solution might be as simple as an adaptable box with a gland and a piece of conduit.

Most sauna heaters I‘ve seen were 6 or 9 kW. Smaller ones are available too.

Also the fact that pulling on the cable while moving stuff suggests that the cable needs to be fixed to the wall.

I was talking about the sockets, French houses are only supposed to have type E sockets. Rewirable plugs are still frequently E or F rather than hybrid, moulded ones are almost exklusively hybrid (CEE 7/7). France has plenty of old CEE 7/1 sockets, probably more than Germany, where non-earthed...

The relevant French standard does require type E sockets though, so type F doesn‘t conform.

As I mentioned, I spend most of my time in Austria. 1.5 mm2 singles in conduit, by far the most common installation method, user to be limited to 12 A before the modern B/C curve MCBs were introduced, as the old L and U curves had much poorer overload protection. With modern MCBs you could go up...

Most plugs are considered double insulated, or so I‘ve been told. Some are only suitable for supplying power to double-insulated appliances while others may also supply earthed appliances. And yes, there are several non-polarised earthed plugs in the world. Belgian ones are used in a number of...

If the electrics have been installed in a sensible manner, you can plug in a heater in every room without tripping anything, probably even with just one 16 A radial per two bedrooms. I‘ve managed to trip a B13 with two heaters but that’s only 3 kW, 16 A is 3680 W and 20 A is 4600 W.

Testing is the only way. Not a real DIY job as it involves opening the CU and testing between the earth bar and the wire at the FCU.

Seems so to me. Adaptor £1.59, three plugs £2.65.

Let‘s assume the typical UK home has one upstairs socket ring. That‘s three heaters on a B32/2.5 mm2. Splitting that very same ring into two 20 A radials gives you four heaters with slightly less cable. A 2 BR would work with just one 20 A radial.

Same category as an electric fire I‘d say. All the portable electric heaters I‘ve seen are below 10 A, so you could run two of them on a 20 A radial. In reality you might even be able to run three, both because many electric heaters are on thermostats and won‘t be on all the time and because a...

Exactly, if that. The only big loads outside the kitchen are electric fires and hair dryers. Even in the kitchen only hobs and ovens are likely to exceed 10 A. Kettles sometimes do but are only on for a minute or so per brew. I can say from experience (living in Austria for a very long time)...

True, once one RCD trips the other one should no longer see an imbalance. In my experience it’s still extremely likely that both RCDs trip in this scenario though.