Search results

Any 2 core will do for a temp. repair just look in you conection box where the cable enters your house and see which pair are used then connect both ends of your 2 wire to the same pair at each end and insulate. Crimps will do or solder and shrink tube and amalgamating tape If you particularly...

Even my laptop and phone charger get noticably warm.. But not too hot to touch, which is something to be concerned about.

You need to find the full model number and check that something like this is the correct part. https://spares-online.co.uk/product/hisense-washing-machine-heater-element-with-ntc-genuine-hk1933068/ You need to check the element for continuity across the 2 outer termiinals not the wiring to them...

Don't really know anything about your hob, but apperently it needs to be well ventilated around the sides that are let into the worktop. If it has been like that from new perhaps that is the problem. Check the instalation dimensions here. Select translate to English where indicated...

Something like this might be reasonable https://toughenedglasssystems.co.uk/product/korniche-roof-lantern-new/?gad_source=1&gad_campaignid=22041968370&gclid=CjwKCAjwgO7RBhBKEiwAZNP85tLhfQydZ4gj3Ki5NvTX0FlsIez1evHlZayvh2AkAVfsR-dhoE0bKhoCOM0QAvD_BwE

Yes, there will be either 1 wire to each terminal and one to the element body (earth) or 2 wires together on one side and one on the other. Just replace them in the same order as you remove them. Taking a pic before you start might be a good idea. Depnding on your meter you will get a low...

Anonymous enough for me. :LOL: Perhaps declining cookies on all sites helps but don't know enough about software to decide.

Hope he only recogniises names and not nom-deplumes with numbers :LOL: :LOL:

A shorter piece is better and more secure in the middle than on the end. You would be calling him back to refix it after a storm. You won't notice it next week. Perhaps the heat is affecting you too.

i think your wire mesh may be defeating the object. the collection of so many leaves won't help anything when soaked in water. As Deluks says clean all the other debris from behind it at the same time and seal it once refitted

I would second gabion baskets in your situation. No more expnsive and just as easy to wheel rocks as blocks. Wood rots so definately a false economy

If you have a multi meter disconnect the leads to the heater element and check for continuity (step 3 above)

All of it back to the leaves.

I guess you checked that there was no damage to belt and other drive components while you were checking for brushes. Was the drum free to turn by hand. Did the water drain ok. Are there any error codes. Is it the same in all modes.

Thin bit is one of the old flower stamen, it's the part of the flower that had the pollen and sometines seeds are formed. What you call the the inner stem is where the petals of the flower were attached. The outer stem is where the flower bud would have begun it's life and developed into a flower.

I presume it is a centrifugal clutch then ?

You just need to remove the flower head stalks and leave to allow the bulb to build up for next year. By late Autumn it will have shed it's leaves and juse leave the main stalk. Once that has gone dry and brittle, either late winter or early spring just wiggle the stem until it easily comes...

Any help

Don't think they are trolling him ( although not really sure what that means ) Just worried about his sanity and wondering if he should be allowed out in a car

I think that is a volt free stat which means it just switches whichever voltage is supplied to it by a boiler or programmer but it might have a mains voltage supplied to it to make it operate. Carefully take it off the wall and see if it has 4 wires going into the back of it. You can test it...