Search results

So a 15/22mm in line pressure gauge? What make/manufacturer do you recommend?

Ok. What sort of drain valve is best to install on 15mm hot/cold water pipe?

Literally shove insulation under the bathtub leaving no gap? I have spare roofing breathable membrane which I think I should envelop the rockwool that I would shove under the bathtub to allow me to easily get the insulation out if needed

Yes the insulation needs to be in in contact with the underside of the bathtub. Rockwool is fine I can use insulation netting to retain heat. Have you used rockwool on the underside of bathtubs to retain heat?

How does underfloor insulation not improve heat retention in the hot water of the above floor bathtub? The whole point of insulation is to keep heat in. And there is a 0.5m2 hole under the bathtub because of poor installation which suck heat out of air below the metal bathtub. The boiler hot...

The analogue pressure gauge on the boiler itself which only displays the radiator flow/return pressure. Don't know if static or dynamic. Probably static. I said previously that I turn down the hot water outlet temperature to a setting of 4/7 (boiler outlet temperature about 65oC) because of...

The lowest point available for a 15mm drain valve is in the garage which is below the property. The boiler is in the garage sat on concrete floor. When the boiler is turned off, as the outlet water pressure is between 1.5 to 2.5 bar when the boiler is off, I think the pressure should be 1.5-2.5...

Why? Because 1) there is a long stretch of about 15m from front to back, 2) I think there is a pressure loss and the original hot water pipe is 15mm copper which, despite lagging, still delivers a lukewarm bath and 3) There are more properties being build nearby which is straining an already...

I'm looking to drain down my hot water (tap) pipe before replacing 15mm with 22mm hot water pipe. I have added a 15mm drain valve to my cold water pipe and plan to do the same to my hot water pipe. This is to stop, after I turn the boiler off and cut the hot water (tap) pipe from leaking...

I have lots of other wood working projects such as 3"x2" framing for a false wall and separately for a shed. Both could use nail guns. Could a 15ga nail gun work?

What nailgun uses 15 gauge collated nails? Usually 1st fixing nailguns only do 16 gauge. Should I get 14 gauge long nails to make sure that for structural timber/framing is nailed together?

I plan to do lots of things 1) Nailing together two 3"x2" CLS timbers together (e.g. noggins) and CLS timber to mini joist hangers. For lowering ceiling height. Frame itself only holds insulation and plasterboard. 2) 3mm thick 1.2m wide x 2.4m long plywood nailed onto inside structure of...

I think I can use a 18 gauge nail fired from a nailgun on the 3mm plywood but can I use a 18gauge nail on the 18mm chipboard? Otherwise I was going to get a 90mm (max penetration depth) 1st fixing nailgun which uses 16gauge nails. Something like one of those Dewalt ones but I want a corded...

Carrying on the thread - I have now insulated the shed with a mix of 50mm block insulation and 50mm mineral wool and put breathable membrane both sides. Am now cladding the inside of the shed using a mix of 18mm chipboard and 3mm plywood. I think I can use a 18 gauge nail fired from a nailgun...

To insulate a wooden shed I'm thinking of stapling breathable membrane to the inside, then put mineral wool (or block insulation) against this membrane, then 3mm ply board (or spare 18mm chipboard) against the insulation. Finally to finish off I would cut occasional circular holes through the...

If the Manufacturer was not in China. They make cheap appliances by the million and 1 complaint is unlikely to make a difference

What about using a 5A rocker switch halfway and said switch would allow add in 0.75mm2 twin cable

I need to lengthen a 0.75mm2 twin (live/neutral) cable on a 25W 220-240V 50Hz bug zapper by about 1m to reach a socket on the floor. The existing socket is 13A (could do reducing to 3A). I need to take apart the zapper to disconnect live/neutral and rewire with said cable then reconnect to a...

These metal plates: https://www.screwfix.com/p/sabrefix-protecta-safe-plates-galvanised-90mm-x-45mm-20-pack/30038#product_additional_details_container)?