Search results

they seem to be cheap enough but i assume you need a matched pair or a sender and recievers what i am trying to achieve is basic internet searches possibly maybe iplayer to watch live or on catch up around 20m from the router at the back off the house where internet is a very poor signal but on...

no problem really your requests are reasonable and similar /connected and in line so in my eyes no problem as i am and most on here are easy going ;)

that is very very strange the only possible source off heat and in my eyes should never happen is from the windings [the motor] dissipating through the shaft to the collet but iff not under load a free running motor will only be perhaps 15-20% load so zero heat build up so no heat to dissipate...

that should never happen heat can only be generated in the collet and nut by slipping as in not enough friction to stop the cutter rotating at a slower rate so likely problem a 12mm shank in a 1/2"[12.7 ]collet or collet loose both are extremely dangerous as the cutter can fly out typical signs...

my pension has gone up by more than 24% over the last 3 years as its compound something like 8.6/10.1 and 4.1 and as said the youngsters who are struggling and cant afford mortgages are paying for it

2 or three or 4inch nails hold bracket or baton in position thump nail in at two positions and when happy its level then nail every position now the nails are just markers so when removing note the holes/dents or marks and highlight them with marker pen or pencil and iff required drill for...

I wonder iff there are any unintended consequences as you will have 3 separate protection circuits possibly competing or overulling each other??? Probably worth keeping a close eye in use and not leave batteries plugged in until you know the play nicely together ??

offer now closed

i am presently with british gas on lower standing charge tarrif or i was over the last year if i had a smart meter i could get free sunday afternoon electric units now this sounds great but is is virtuallty zero value as i dont have a smart meter but most off all my base load is about 2.7...

they are a good idea for most people but downsides you need to be aware off they can remotely disconnect you they can remotely change to a prepayment meter or charge you more per unit without your permission if they make a mistake now these are all legitimate actions if situations require it...

if what you say about ownership is correct then you are 100% correct indeed its criminal damage to touch your gate beyond the normal use so stealing your gate and the criminal act off.................................................... ..................................now in the real world...

probably not much but because you have end and cross-grain side by side they move at different rates but as you say well climatized reduces the risk

just make sure you dont leave the adaptors on the batteries when not actually in use as parasitic draw can fully drain a battery and dead li-ions batteries cant be charged

my thoughts quite a stunning table as it is any infill will detract from the look from a little bit to perhaps quite a lot infill needs to be flexible or risk cracking in general, place mats under plates means only the odd crumb may stray and a soft cloth and perhaps soft bristle brush will...

whilst i agree with trusted institutions, they should not ask for unessiserally accurate information when not required as most by default will give accurate information automatically

programs compose by people with one agenda to get to the goal they need with possibly more sellable data rather than a real person compatible tick list asking someone's birthdate is wrong on several levels as pinpoint accurate information is 100 time more dangerous than "just enough to confirm"...

normally over £60 battery offers like this tend to be more off an annual event...

as an aside iff you go in a vertical or horizontal direction in a strait line is there any electrical items like sockets switches blanking plates light fittings along those lines?? these are areas you should not touch[leave a 75mm corridor iff possible to be safe but 30mm minimum] but still well...

check 100% what is involved and you are responsible for words like "buyer removes "may be turn up with a luton van and take it from the garden up to its still plumbed in and you have to remove and repair damage caused in the process

other ways to remove allen key bolt correct allen key and lever hard sideways to force key to grip the bottom off one side and the top off the other select a screwdriver that will fit corner to corner and tap hard if it grounds before going tight grind a bit off the blade point if it wont go in...